Measurement Computing USB-1608FS-Plus User Manual Download Page 2

HM USB-1608FS-Plus.docx 

Trademark

 

and Copyright

 

Information

Measurement

 

Computing

 

Corporation,

 

InstaCal,

 

Universal

 

Library, and the

 

Measurement

 

Computing logo are

 

either trademarks

 

or registered trademarks

 

of Measurement

 

Computing

 

Corporation. Refer to the

 

Copyrights

 

&

 

Trademarks

 

section on

 

mccdaq.com/legal

 

for

 

more

 

information about

 

Measurement

 

Computing trademarks. 

Other

 

product

 

and company

 

names

 

mentioned herein are

 

trademarks

 

or

 

trade

 

names

 

of their

 

respective

 

companies.
©

 

201

Measurement

 

Computing

 

Corporation. All

 

rights

 

reserved. No part

 

of this

 

publication

 

may be 

reproduced, stored in

 

a

 

retrieval system, or transmitted, in any

 

form

 

by any

 

means, electronic,

 

mechanical, by

 

photocopying, recording, or

 

otherwise

 

without

 

the

 

prior

 

written

 

permission of

 

Measurement

 

Computing

 

Corporation.

Notice

Measurement Computing Corporation does not authorize any Measurement Computing Corporation product for 

use in life support systems and/or devices without prior written consent from Measurement Computing 

Corporation. Life support devices/systems are devices or systems that, a) are intended for surgical implantation 

into the body, or b) support or sustain life and whose failure to perform can be reasonably expected to result in 

injury. Measurement Computing Corporation products are not designed with the components required, and are 

not subject to the testing required to ensure a level of reliability suitable for the treatment and diagnosis of 

people.

Summary of Contents for USB-1608FS-Plus

























Reviews: