Measurement Computing BTH-1208LS-OEM User Manual Download Page 24

Page: 24 / 27

BTH-1208LS-OEM User's Guide

Specifications

Power

Table 17. Power specifications

Parameter

Condition

Specification

Supply current, USB source

During enumeration

< 100 mA

After USB enumeration or
connected to USB charger /
supply

< 500 mA

Battery power (Note 8)

Two AA or two AAA cells
Alkaline, NiCd, and NiMH cells supported

Battery charging

NiMH and NiCd charging supported.
Alkaline cells automatically detected and not
charged.

+VO power available

After USB enumeration or
Bluetooth connection

3.3 V nominal

+VO output current

After USB enumeration or
Bluetooth connection

50 mA max

Note 8:

When operating from batteries there is a user configurable power-off timer that will turn the device off
when there is no host connection for the specified amount of time. The timer can be disabled or set to a
value from 1 – 255 minutes.

Bluetooth

Table 18. Bluetooth specifications

Parameter

Specification

Device type (Note 9)

Bluetooth 2.1

Device compatibility

Backwards compatible with Bluetooth 2.0, 1.2, and 1.1

Bluetooth profile

Serial Port Profile (SPP)

Radio range

Class II, 10 m typ

Note 9:

The Bluetooth radio is disabled when the device is connected to a USB host.

USB

Table 19. USB specifications

Parameter

Specification

Device type

USB 2.0 full speed

Device compatibility

USB 1.1, USB 2.0

Environmental

Table 20. Environmental specifications

Parameter

Specification

Operating temperature range

0 °C to 50 °C

Storage temperature range

–40 °C to 70 °C

Humidity

0% to 90% non-condensing

Summary of Contents for BTH-1208LS-OEM



























Search results

Summary of Contents for BTH-1208LS-OEM

Reviews:

Related manuals for BTH-1208LS-OEM

Brands by name

Popular brands

Measurement Computing BTH-1208LS-OEM, User Manual

Search results

Summary of Contents for BTH-1208LS-OEM

Reviews:

Related manuals for BTH-1208LS-OEM

Brands by name

Popular brands