MDC XT17HRT 2022 Owner'S Manual Download Page 6

Page: 6 / 112

www.marketdirect.com.au

Ph: 1300 494 494

©Copyright

P a g e

Coupling Mass

Reading = Tare Mass

Introduction

Off road caravanning is a rewarding way to travel and see our great country. Owning an MDC Caravan

will afford you the opportunity to travel to remote places and stay in comfort. It is the intention of

MDC for you to have the best possible owner experience and enjoy the great outdoors.

Terminology & Abbreviations

Tare Weight:

The total weight of the trailer (load on tyres plus coupling load) with all options and

fittings as supplied by the manufacturer, with empty water tanks, excluding fluids not essential for

operation on public roads, and without luggage or personal effects.

ATM (Aggregate Trailer Mass) Rating:

The total permissible mass of the Trailer. This includes the coupling

mass and whatever you add as payload (e.g. water, gas, luggage) up to the specified rating. The ATM Rating

must not be exceeded.

GTM (Gross Trailer Mass) Rating:

The total permissible mass that can be supported by the wheels/ tyres of

the Trailer. This includes whatever you add as payload (e.g. water, gas, equipment and luggage), but does

not include the mass supported by the tow vehicle. The GTM Rating must not be exceeded.

Caravans for illustration purposes only.

Load

Coupling Mass

Reading must not exceed ATM Rating

Summary of Contents for XT17HRT 2022

















































































































Search results

Summary of Contents for XT17HRT 2022

Reviews:

Related manuals for XT17HRT 2022

Brands by name

Popular brands

MDC XT17HRT 2022, Owner'S Manual

Search results

Summary of Contents for XT17HRT 2022

Reviews:

Related manuals for XT17HRT 2022

Brands by name

Popular brands