background image

 

19

 

 

1300 4X4 4X4 

mounted on the drawbar with a steel wire lanyard to connect to your tow vehicle. If the caravan becomes detached, 
the lanyard will pull the pin from the breakaway switch and the onboard batteries will activate the brake system. The 
lanyard must be attached to a solid part of the vehicle. It is a requirement that power be supplied by the tow vehicle to 
the breakaway power source while towing. This is done via the 50amp Anderson Plug on the drawbar. Consult a 
qualified auto electrician to ensure this is fitted to your tow vehicle. 

In NSW there is an additional requirement that the breakaway power source be monitored from the driver position with 
a minimum of a “visual alarm” for low battery voltage. Consult a qualified auto electrician to ensure this is fitted to your 
vehicle. 
          Breakaway Switch 

 

 

 

 

 

Anderson Plug 

 

 
 
 
 
 
 
 

CAUTION: 
DO NOT CONNECT THE BREAKAWAY LANYARD TO THE SAME POINT AS THE SAFETY CHAIN SHACKLES. 
DO NOT USE THE BREAKAWAY AS AN ALTERNATIVE TO THE HANDBRAKE AND DO NOT REMOVE THE PIN 

AS AN ALTERNATIVE SECURITY MEASURE. REMOVING THE PIN WILL RAPIDLY DISCHARGE THE 
BATTERIES. 
 
 
 

 

 

 

Summary of Contents for XT11E














































Reviews: