background image

Pre-installed

3

 6

 11

 2

 3

 4

 5

 1

 7

 8

 9

 10

 12

 13

 14

 15

 16

 17

 18

 19

 20

21

 22

 23

 24

 25

26

 27

 34

 28

 29

 30

31

32

33

57001 PARTS LIST

Pre-installed

Pre-installed

Wrench

1 Piece 

Plastic Pole Insert

2 Pieces 

3 x 26mm Screw

4 Pieces 

Lock Pin

2 Pieces

Allen Key

1 Piece 

Board L Tube

2 Pieces

 

Board Tube

2 Pieces

Left Tube

1 Piece

Left L Tube

1 Piece

Right L Tube

1 Piece

Support Tube

2 Pieces

Mounting Tube

2 Pieces

Ramp Tube

2 Pieces

Ramp L Tube

2 Pieces

Switch Sensor

1 Piece

Net

1 Piece

Rim Support Plate

1 Piece

Rim 

1 Piece

Basketball

2 Pieces

Ramp U Tube

1 Piece

Horizontal Tube

2 Piece

Ramp Net

1 Piece

Electronic Scorer

1 Piece

Backboard

1 Piece

M6 Washer

34 Pieces

M6  x 20mm Bolt

8 Pieces

M6  x 29mm Bolt

6 Pieces

M6  x 35mm Bolt

2 Pieces

M6  x 42mm Bolt

4 Pieces

M6  x 50mm Bolt

4 Pieces

M6 Nut

24 Pieces

Inflation Pump

with Needle

1 Piece

Right Tube

1 Piece

Pre-installed

Spring Lock

9 Pieces 

TIME

SCORE

WARNING:

!

1) Require 4pcs AA Batteries (Not included).

2) Do not mix old and new batteries.

3) Do not mix alkaline, standard (carbon zinc), or rechangeable (nickel-cadmium) batteries.

Summary of Contents for 57001






















Reviews: