McQuay MicroTech II N2 Installation And Maintenance Manual Download Page 12

13600 Industrial Park Boulevard, Minneapolis, MN 55440 USA (763) 553-5330 (www.mcquay.com)

Service Information

Test Procedures

If you can control the unit from the keypad but are unable to communicate with it via the network,
try the following:

 

Verify the network (bus) wiring

 

Check the integrity of the cable harness to the network terminals

 

Verify that the N2 address (SW1) is set to a unique binary number between 1 and 253.

If the MicroTech II N2 Open communication module still doesn’t respond, replace the
communication module.

List of Replaceable Parts

Network Connection Plug

Generic Replacement Parts

The three-contact network connector plug has custom markings, but if you lose this terminal block
you can replace it with a standard block without the markings from a manufacturer. The list below
contains manufacturers part numbers for equivalent parts without the custom markings.

Manufacturer

Telephone

Order Number

Phoenix Contact

(800) 888-7388

17 57 02 2

Altech Corp

(908) 806-9400

37.003

Direct Replacement Parts

You can order direct replacement parts for these connector plugs from McQuay International
(1-800-37-PARTS).

Part Number

Description

AS-TBKIT-0

5 terminal blocks marked REF, N2- and N2+

Kit 

Component

Description

Part No.

Kit

N2 communication module for unit ventilators with standoffs

107293125

Summary of Contents for MicroTech II N2













Reviews: