mcmurdo S4 Rescue SART Service Manual Download Page 22 | Manualshive

Page: 22 / 27

background image

Commercial in confidence

Page 19

mcmurdo

mcmurdo

mcmurdo

mcmurdo

5.3.

Re-tune PCB

Although it is possible to perform alignment of the PCB in the field, this is not a recommended
procedure because it requires specialised test equipment and suitably qualified technicians.

It is strongly recommended that PCBs are returned to McMurdo for calibration.

5.4.

Factory return procedure

If a SART cannot be repaired in the field, it should be returned to the factory.

The SART assessment form must be completed and returned with the SART to show the tests
which have been performed and the results obtained.

«
...
20
21
22
23
24
...
»

Summary of Contents for S4 Rescue SART




























Reviews:

No comments

Related manuals for S4 Rescue SART

Brand: iHome Pages: 13

Brand: Quick Pages: 24

Brand: VEF Pages: 3

Brand: Vertex Standard Pages: 2

Brand: Yaesu Pages: 6

Heritage Bluetooth

Brand: HAEGER Pages: 40

Brand: Denver Pages: 13

Brand: Sparc Pages: 2

Brand: B&G Pages: 20

CSMP162 - AM/FM Dual Alarm Clock/Radio

Brand: Coby Pages: 1

Brand: Fusion Pages: 17

Brand: Uniden Pages: 72

Brand: Telefunken Pages: 18

Brand: Anysecu Pages: 4

Brand: SLIVE Pages: 2

Brand: JRC Pages: 2

Alphatron Marine AlphaTurn

Brand: JRC Pages: 57

Brand: Alinco Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands