McLaren coupe series Owner'S Handbook Manual Download Page 213

Page: 213 / 272

Maintaining Your McLaren

Fuses

5.21

NOTE: Do not lower the closing panel
further than necessary as it could be
damaged.

5. Remove the appropriate fuse and

replace it with a fuse of the same value
as the original. If in doubt, check the
fuse specification chart.

6. Raise the closing panel into position, fit

the clip and fit and tighten the two
front screws.

Secondary fuse box fuse specification
chart

Battery fuse box

Battery fuse box access

1. Open the luggage compartment lid and

remove any items stowed inside.

2. Remove the 2 screws securing the top

of the battery access cover.

No.

Amps

Circuit protected

Driver’s door

Passenger’s door

Lights

Body

Alarm

Off Board AM/FM Tuner

USB AUX Module

F10

Air conditioning

F11

Alarm Control Unit

F12

Tracker

F13

7.5

Alarm

F14

Instrument cluster

p13.book Page 21 Wednesday, April 26, 2017 9:22 PM

Summary of Contents for coupe series

















































































































































































































































































Search results

Summary of Contents for coupe series

Reviews:

Related manuals for coupe series

Brands by name

Popular brands

McLaren coupe series, Owner'S Handbook Manual

Search results

Summary of Contents for coupe series

Reviews:

Related manuals for coupe series

Brands by name

Popular brands