McLaren coupe series Owner'S Handbook Manual Download Page 158 | Manualshive

Page: 158 / 272

background image

Instruments

Instrument Cluster Display

3.28

Messages - Coupe, GT and Spider

The instrument cluster may show messages
that refer you to the owner manual. The
table below indicates what you should do
when one of these messages is displayed.

WARNING: Do not ignore warning
messages, failure to take
appropriate action may result in
injury or damage to the vehicle.

Message

Action

Battery management active

The vehicle is not be able to supply enough voltage and has activate power saving mode. The
climate control and steering will operate with reduced effect. See Power saving mode, page 2.2.

Brake fluid level low

Top up brake fluid, see Brake fluid, page 5.9.

Clutch over temperature

The vehicle has been subject to extreme operating conditions. This may be caused by excessive hill
starts, repeated hard acceleration, driving slowly up steep hills for extended periods. As a result, the
gearbox may limit engine torque.
Stop the vehicle and allow the engine to idle in neutral for a few minutes.

Clutch temperature high

The vehicle has been subject to extreme operating conditions. This may be caused by excessive hill
starts, repeated hard acceleration, driving slowly up steep hills for extended periods. As a result, the
gearbox may limit engine torque.
Stop the vehicle and allow the engine to idle in neutral for a few minutes.

Engine oil level high

See Checking the engine oil, page 5.2.

Engine oil level low

See Checking the engine oil, page 5.2.

ESC OFF not possible

The ESC deactivation conditions have not been met. See Electronic Stability Control, page 2.31.

ESC reduced not possible

The ESC reduction conditions have not been met. See Electronic Stability Control, page 2.31.

Front left tire over inflated

Stop the vehicle and inspect wheels and tires, see Inspecting wheels and tires, page 5.34.

Front left tire over temperature

Stop the vehicle and inspect wheels and tires, see Inspecting wheels and tires, page 5.34.

p13.book Page 28 Wednesday, April 26, 2017 9:22 PM

«
...
156
157
158
159
160
...
»

Summary of Contents for coupe series

















































































































































































































































































Reviews:

No comments

Related manuals for coupe series

Brand: Accel Pages: 2

Brand: Calix Pages: 5

ANDROID INTERFACE

Brand: GMC Pages: 18

Brand: Prorack Pages: 15

Brand: Van Guard Pages: 3

Brand: Vauxhall Pages: 259

Brand: iOttie Pages: 58

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Sanitas Pages: 36

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: Kia Pages: 58

Brand: GYS Pages: 32

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 16

2000 Accord Sedan

Brand: Honda Pages: 320

Pro Competition

Brand: G-Tech Pages: 180

Brand: Ace K9 Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands