McIntosh MHT200, Service Manual, Page: 2 / 60

PERFORMANCE SPECIFICATIONS
2
Preamplifier and Processor Specifications
Frequency Response
Stereo:
Left and Right Loudspeakers: +0-0.5dB from 20Hz-20,000Hz
Music 1-4:
Left, Center, Right Loudspeakers: +0-0.5dB from 20Hz-
20,000Hz
Large Surround Loudspeakers: +0-0.5dB from 20Hz-
20,000Hz
Pro-Logic:
Left, Center, Right, Large Loudspeakers: +/-0.5dB from
20Hz-20,000Hz
Large Surround Loudspeakers: +1-3dB from 20Hz-6.3kHz
Subwoofer
1 : 20Hz-140Hz
Dolby Digital, DTS and External Input:
Left, Center, Right Large Loudspeakers: +/-0.5dB from 20Hz-
20,000Hz
Large Surround Loudspeakers: +/-0.5dB from 20Hz-
20,000Hz
Subwoofer
1
: 20Hz-140Hz
Rated Output
2V for all channels
Input Impedance
22k ohms
Output Impedance
Less than 560 ohms for all channels
Maximum Output Voltage
8V
Total Harmonic Distortion
0.05% for all channels
Sensitivity
Analog Input: 100mV IHF
Dolby Level: 200mV Input
External Input: 200mV for 2.0V Output
Signal To Noise Ratio
Greater than 90dB A-weighted
Maximum Input Signal
Analog Input: 6Vrms
Tone Controls
+/-12dB from the flat setting
1
If any of the channels have the Loudspeaker Setting of Small, the
subwoofer has a electronic low pass filter with a corner frequency of
80Hz and a 24dB per Octave roll-off in all modes except external.
The Frequency Response of the Subwoofer Channel is also
determined by the Crossover Setting.
Power Amplifier Specifications
Power Output
Minimum sine wave continuous average power output per
channel, all channels operating is: 100 watts into 4 ohm load, 70
watts into a 8 ohm load
Rated Power Band
20Hz to 20,000Hz
Total Harmonic Distortion
Maximum Total Harmonic Distortion at any power level from
250 milliwatts to rated power output is: 0.05% for 4 or 8 ohm
load
Dynamic Headroom
1.8dB
Frequency Response
+0, -0.25dB from 20Hz to 20,000Hz
+0, -3dB from 10Hz to 1000,000Hz
Sensitivity
1.0 Volt
A-Weighted Signal To Noise Ratio
92dB (112dB below rated output)
Intermodulation Distortion
Maximum Intermodulation Distortion if instantaneous peak
output per channel does not exceed twice the rated output, for
any combination of frequencies from 20Hz to 20,000Hz, with all
channels operating is: 0.05% for 4 or 8 ohm loads
Input Impedance
20,000 ohms
Wide Band Damping Factor
100 at 4 ohms
200 at 8 ohms
General Specifications
Power Requirements
100 Volts, 50/60Hz at 8.4 Amps
110 Volts, 50/60Hz at 7.7 Amps
120 Volts, 50/60Hz at 7.0 Amps
220 Volts, 50/60Hz at 3.5 Amps
230 Volts, 50/60Hz at 3.5 Amps
240 Volts, 50/60Hz at 3.5 Amps
Note: Refer to rear panel of the MHT200 for the correct voltage.
Dimensions
Front Panel: 17-3/4 inches (45.09cm) wide, 9-7/16 inches
(23.97cm) high. Depth behind front mounting panel is 19 inches
(48.26cm) including clearance for connectors. Panel clearance
required in front of mounting panel is 1-1/8 inches (2.9cm).
Weight
73 pounds (33.1kg) net, 87 pounds (39.5kg) shipping