background image

3

Table of Contents

Important Safety Instructions

 ��������������������������������������� 2

Thank you from all of us at McIntosh

 ��������������������������� 2

Make a Note

 ������������������������������������������������������������������ 2

Ready To Perform

 ��������������������������������������������������������� 3

Choosing the Right Spot

 ����������������������������������������������� 3

Installation

 �������������������������������������������������������������������� 3

Fine Tune

����������������������������������������������������������������������� 4

Speaker Diagram

 ���������������������������������������������������������� 4

Warranty

 ����������������������������������������������������������������������� 5

Specifications

 ���������������������������������������������������������������� 6

Drivers ��������������������������������������������������������������������������� 6

Ready To Perform

The CS200 Ceiling Loudspeaker System is designed to 

provide exceptional performance. This 3-way speaker 

features an 8 inch Woven Glass Fiber Woofer. Above the 

Woofer sits an adjustable array with a Titanium Dome  

tweeter and two Titanium Inverted Dome midrange 

speakers from McIntosh’s acclaimed XRT speaker line. 

The Midrange drivers and Tweeter are arranged in a 

modified MTM array for optimal performance of the 

high-end drivers. 

The Low Profile Micro-Flange Grill is magnetically held 

in place. These grills are ready to be painted if you wish.

Choosing the Right Spot

There are a few important things to consider when 

choosing a location to mount the CS200:
•  Can the location support at least 5 times the weight 

of the CS200? This will be a vibrating mass located 

possibly above your head. Make sure the material 

where the CS200 will be mounted can hold more 

than 30 pounds and is at least 3/8 inch (0.9525cm )

thick and a maximum of 2 inches (5.08cm). A depth 

of at least 5 inches (12.7cm) is required.

•  Can you run the necessary wires to the CS200?
•  Is the position optimal for the purpose the speaker 

will serve?  Obviously, 2-channel and home theater 

applications will have different speaker placement 

considerations. Your McIntosh Dealer is an excellent 

resource for speaker installation.

•  Are there any obstacles that should be avoided like 

heating and cooling ducts or high humidity from a 

shower or sauna? And, of course, you should obey 

all applicable building codes.

Installation

1.  After choosing the right spot, use the supplied 

template to mark the area to be cut out. 

2.  For dry wall installation, use a drywall knife or saw 

to cut a hole (see figure 1.1 on page 4). The hole 

should be 9-5/8 inches (24.4475 cm) in diameter. The 

full diameter of the CS200 is 11 inches (27.94cm) 

For new construction, the RK200 rough-in bracket 

is recommended. The RK200 is available from your 

McIntosh Dealer.

3.  Prepare Speaker Wires for connection to the CS200. 

Remove ½ inch (12.7 mm) of insulation from the 

wire end and twist the strands together. For runs 

under 25 feet use at least 16AWG wire. For runs 

under 50 feet use at least 14AWG, and for longer 

runs up to 100 feet use 12AWG. 12AWG, being 

the larger wire, can be used in all the above cases 

if desired. Thicker wire may not fit in the speaker 

terminals.

4.  Connect the exposed end of the wires to the spring-

loaded terminals. Push the terminal to open the hole. 

Insert the wire making sure no loose strands are 

exposed. Connect the positive speaker wire to the red 

terminal and the negative to the black terminal. 

Releasing the terminal will provide a secure 

connection.

5.  Carefully place the CS200 in the opening you 

prepared in Step 2. You may choose to place some 

fiberglass insulation loosely behind the speaker for 

better isolation. 

6.  Using a #2 Phillips screwdriver, loosen the 4 

clamping screws one turn counter-clockwise (see 

diagrams on page 4). This will release the clamp. 

Note the four clamp screws will be higher than the 

nearby recessed screws.

7.  Tighten the four screws evenly, turning each one 

slightly in turn until each is tight. 

8.  Carefully install the Grille. The Grille is held in place 

by magnets.

9.  Enjoy.

Summary of Contents for CS200







Reviews: