McDonnell & Miller 1575 Series Instruction Manual Download Page 2

2

Electronic Control Unit

Burner Relay Time Delay

The field-adjustable time delay (DOB) helps to 
p r event nuisance bu rner shut-dow n . The number 
of seconds water needs to be off the longest probe
b e fore the bu rner will shut down can be set
b e t ween 0 and 60 seconds.

Redundant Low Water Cut-Off

When the boiler water drops below the middle
p r o b e, a 3 minute timing circuit will be activa t e d . I f
water does not return to the middle probe within
three minu t e s, the bu rner relay will shut dow n . T h e
Red LED will flash once eve ry second if this 
condition occurs.

• Automatic Reset units will automatically reset 

when the water level is restored to the middle probe.

N OT E : The timing circuit will automatically reset 
if the water level returns to the middle probe within
3 minu t e s.

Redundant Pump Off

The pump relay will be activated, turning the pump
on after water drops below the middle probe. If the
water level is not restored to the top probe within 3
m i nutes the pump relay will be deactivated, shutting
off the pump. After the pump relay is deactiva t e d ,
n o rmal operation is resumed. Water must again
drop off the middle probe to activate the pump
r e l ay. There is no LED signal for this occura n c e.

A d j u s t a ble Pump Diffe r e n t i a l s

The water level positions for turning the pump on
and off and obtaining the needed pump diffe r e n t i a l s
are changed by cutting the length of the middle and
s h o rtest probes.

California Proposition 65 warning!  This product contains chemicals known to the

state of California to cause cancer and birth defects or other reproductive harm.

Previous controls should never be installed on a new system. Always install new

controls on a new boiler or system.

CAUTION:

A more frequent replacement interval may be necessary based on the condition of

the unit at time of inspection. McDonnell    Miller s warranty is one (1) year from date

of installation or two (2) years from the date of manufacture.

Failure to follow this warning could cause property damage, personal inj ury or death.

!

&

'

Summary of Contents for 1575 Series













Reviews: