background image

14

MAINTENANCE

LUBRICATION CHART

GENERAL RECOMMENDATIONS

The warranty on this tractor does not cover items that have 

been subjected to operator abuse or negligence.  To receive 

full value from the warranty, operator must main tain tractor 

as instructed in this manual.
Some adjustments will need to be made periodically to 

properly maintain your tractor.
At least once a season, check to see if you should make 

any of the adjustments described in the Service and 

Adjustments section of this manual.
• 

At least once a year you should replace the spark plug, 

clean or replace air filter, and check blades and belts 

for wear.  A new spark plug and clean air filter ensure 

proper air-fuel mixture and help your engine run better 

and last longer.

BEFORE EACH USE

•  Check engine oil level.
•  Check brake operation.
•  Check tire pressure.
• 

Check operator presence and ROS systems for proper 

operation.

•  Check for loose fasteners.

IMPORTANT:

  DO NOT OIL OR GREASE THE PIVOT POINTS 

WHICH HAVE SPECIAL NYLON BEARINGS.  VISCOUS 

LU BRI CANTS WILL ATTRACT DUST AND DIRT THAT WILL 

SHORT EN THE LIFE OF THE SELF-LU BRI CAT ING BEARINGS.  

IF YOU FEEL THEY MUST BE LU BRI CAT ED, USE ONLY A 

DRY, POW DERED GRAPHITE TYPE LU BRI CANT SPARINGLY.

T

R
A
C

T

O

R

E

N

G

I

N

E

3

2

2

6

1,2

2

2

1

,

2

4

5

1,2

BEFORE

EACH

USE

EVERY

25

HOURS

EVERY

8

HOURS

EVERY

100

HOURS

EVERY

SEASON

BEFORE

STORAGE

EVERY

50

HOURS

1 - Change more often when operating under a heavy load or in high ambient temperatures
2 - Service more often when operating in dirty or dusty conditions.
3 - Replace blades more often when mowing in sandy soil.

4 - Not required if equipped with maintenance-free battery

5 - See Cleaning in Maintenance Section.

6 - Inspect the muffler every 50 hours of operation 

or six months for signs of damage. If damage is 
found, refer to the repair parts list or contact your

 local dealer to order a replacement.

Clean Air Filter

Change Engine Oil (models with oil filter)

Clean Engine Cooling Fins

Clean Air Screen

Replace Oil Filter (If equipped)

Replace Fuel Filter

Change Engine Oil (models without oil filter)

MAINTENANCE  SCHEDULE

Check Battery Level
Clean Battery and Terminals

Lubrication Chart

Check/Replace Mower Blades

Check for Loose Fasteners

Check Operator Presence and ROS Systems

Check Tire Pressure

Check Brake Operation

Replace Air Filter Paper Cartridge

Replace Spark Plug

Inspect Muffler/Spark Arrester

Check Engine Oil Level

Check V-Belts

Check Mower Levelness

Check Transaxle Cooling

Clean Debris off Steering Plate

01964

➁ 

ENGINE

 

FRONT 

WHEEL 

BEARING 

ZERK

 

FRONT 

WHEEL 

BEARING 

ZERK

 

SPINDLE ZERK

 

SPINDLE ZERK

 

General Purpose Grease

  Refer to Maintenance “ENGINE” Section

Summary of Contents for POULANPRO PP19H42

























































Reviews: