Version 12/11
PA-6430 Conference Microphone
Item no. 31 14 61
Intended use
1.
This product is designed to convert acoustic signals (sound waves) into electric signals. It must
only be connected to the microphone input of an audio device (amplifier, mixing desk, etc.). It
must only be used in enclosed spaces and therefore not outside. Do not under any circumstances
expose the device to moisture, such as in bathrooms or similar rooms.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged. In
addition, improper use can cause hazards such as short circuiting, fire, electric shock etc. Read
the instructions carefully and keep them. Make this product available to third parties only together
with its operating instructions.
Delivery content
2.
Microphone
•
Operating instructions
•
Safety instructions
3.
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
Persons / Product
Only connect the product to suitable microphone inputs, to prevent distortions or mismatching
•
that might damage the microphone or any connected audio equipment. Please, to do this also
pay attention to the connection data in the “Technical data” section.
Never point the microphone at the speakers in your loudspeakers, since this may lead to
•
interference, which could damage the loudspeaker and the connected amplifier.
The device is not a toy. Keep it out of the reach of children and pets.
•
Do not leave packaging material lying around carelessly. These may become dangerous
•
playing material for children.
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
•
moisture, flammable gases, vapours and solvents.
Do not place the product under any mechanical stress.
•
If it is no longer possible to operate the product safely, take it out of operation and protect it
•
from any accidental use. Safe operation can no longer be guaranteed if the product:
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
-
Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
•
the product.
Also observe the safety and operating instructions of any other devices which are connected
•
to the product.
Miscellaneous
Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
•
qualified shop.
If you have questions which remain unanswered by these operating instructions, contact our
•
technical support service or other technical personnel.
Operation
4.
Switch off your mixing desk to which the microphone is connected.
1.
Turn the volume of the respective microphone input all the way down.
2.
Connect the microphone cable to a 6.3 mm audio input at the mixing desk.
3.
Switch the mixing desk and the other devices of your audio system on.
4.
Push the red button on the microphone foot to switch the microphone on.
5.
Speak into the microphone and while doing so set the volume and the tone to the desired
6.
values via the mixing desk.
Disposal
5.
Electronic devices are recyclable waste and must not be disposed of in the household
waste.
At the end of its service life, dispose of the product according to the relevant statutory
regulations.
Technical data
6.
Frequency range*:
180 – 10000 Hz
Sensitivity:
-75 dB ±3 dB (0 dB = 1/µbar @ 1 kHz)
Impedance:
600 Ω ±30 % @ 1 kHz
Connection:
6,3 mm jack plug
Directivity**:
Cardioid
Operating temperature:
-20 to +55 ºC
Cable length:
5 m
Dimensions (L x W x H):
99 x 78 x 250 mm
Weight:
345 g
*Frequency range
0°
30°
330°
300°
270°
240°
210°
60°
90°
120°
150°
180°
**Directivity
These operating instructions are published by Conrad Electronic SE,
Klaus-Conrad-Straße 1, D-92240 Hirschau/Germany.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print.
We reserve the right to change the technical or physical specifications.
© 2011 by Conrad Electronic SE.
V1_1211_02-SB
