MBM icreaseAIR Operator'S Manual Download Page 30

Page: 30 / 34

PERFORATING AND SCORING ASSEMBLIES

For removing and old blade and attaching a new blade to the pressure adjust mounting

bracket, remove the (1) button head cap screw. BE SURE TO TIGHTEN THE SET

SCREW SECURELY TO THE BAR. Once you have the upper and lower perf assemblies

in place, you can tighten the half dog screw.

Complete: #S-APP-0129

Complete: #S-APP-0139

Part No.

Description

H-0215

Screw-10-32x1/2” button head

socket

H-0250

Screw-10-32x 1 1/2”socket cap

H-0270

Screw-1/4”-20x1/4” socket set

H-0275

Screw-1/4-20x1/4” socket set

H-0278

Screw-1/4-20x1/4” socket half

dog

H-0456

Washer – flat .20

H-0580

Compression spring 1 ½”

S-AAM-0930

Upper Wheel Assemlby

S-AM-0931

Lower Forwarding Roller Assy

S-AAM-0933

MOLDED ROLLER WHEEL

ASSEMBLY COMPLETE

S-APP-0131

Score blade assembly

S-APP-0143

9-1 Perf blade assembly

S-APP-0132

Lower score hub assy.Hub ap

S-APP-0133

Lower perf assy. Hub app

S-APP-0622

Bracket-perf/score pres,adj.

assy

Summary of Contents for icreaseAIR



































Search results

Summary of Contents for icreaseAIR

Reviews:

Related manuals for icreaseAIR

Brands by name

Popular brands

MBM icreaseAIR, Operator'S Manual

Search results

Summary of Contents for icreaseAIR

Reviews:

Related manuals for icreaseAIR

Brands by name

Popular brands