background image

 

   

2

 

Adjust the seat then put your back firmly against back pad. 

3

 

Insert pin into weight stack at desired resistance level. 

4

 

Arm natural contraction, both hands holding the whip handle. 

5

 

Arm  extension  forward,  slowly  forward  push  movable  arm.  Until  completely 
stretched arm. 

6

 

Keep the status  for  a moment, then slowly return to  the start  position and repeat 
the movement.

 

5. NOTICE

 

1.

  Warm-up

                          It takes 5-10 minutes to warm-up before starting exercise, for instance mark time, 

free-standing exercises etc., in order to move each joint muscle, so as not to injure 
the joint muscle while exercising. 

2.

 

Diet

   

                          Eat  some  more  protein,  vegetables,  and  fruit.  Begin  to  do  exercises  until  40     

minutes  after  a  meal.  Taking  food  until  half  an  hour  after  doing  exercises  and 
drinks little water while doing exercise.

 

3.

 

Breath 

Breathe in while exerting oneself, exhale while      relaxing. To coordinate breathe   
with movement.

   

4.

 

Frequency 

                              It needs to take a rest over 48 hours before exercising the same muscle. 

5 . 

Burden 

Exerciser should choose suitable weight according to one's own actual conditions,   
make  sure  not  to  be  overweight,  so  as  not  to  cause  the  muscle  to  draw  wounded. 
Exercises  should  according  to  the  progressive  principle;  it  is  normal  to  feel  ache 
while exercise for the first time.

 

6.  MAINTENANCE 

1.For  safety  use  of  machines

regularly  maintenance  must  be  implemented.       

Especially for the attrition parts, such as cable, pulley block and connection parts. 

2. Special attention should be paid to easy worn parts. 
3. Replace the damaged components immediately and stop    using the machine until 

it is fixed. 

4. Maintenance should be made as following instruction. 

7. ASSEMBLY

 

All the content of user’s manual is to assure the strength training machine can be 

Maintenance 

Daily 

Weekly 

3 Month 

Check the connection parts, pulley and balance weight 
group 

 
√ 
 

 

 

Clean cushion and shield 

√ 
 

 

 

Lubricating needed parts 

 

 

√ 
 

Check the whether the screws are loosen or not 

 

√ 
 

 

Lubrication: bearing 

 

 

√ 
 

Summary of Contents for MV-014













Reviews: