Settings for Best Performance
8
Q1.1500D
General:
At this point you are ready to get more specific on the settings for your amplifier.
Phase:
Time alignment, typically recommended at 0 degrees unless using multiple amps and subs in both the front and rear of the vehicle. The Phase can be adjusted to give the perception of bass reaching
the listener at the same time regardless of location.
Subsonic:
This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o’clock position is a
great starting point. EXAMPLE: If you adjust the Subsonic to 25Hz, the amplifier will not play frequencies below 25Hz but will play frequencies from 25Hz to the chosen Low Pass frequency.
Bass Frequency:
This setting is used for selecting the frequency you want to focus your enhancement on. Suggested enhancement is from 35-45Hz, but you should be careful not to set enhancement below the F3 or
-3dB point of your sub/enclosure combo.
Bandwidth:
This setting controls the amount of frequencies included in the Bass Boost. The bandwidth varies from narrow to wide in a pyramid style boost with the selected Bass Frequency value being the
center.
Bass Boost:
This setting adjusts the amount of boost on the selected Bass Frequency and Bandwidth. This setting is variable from 0-12dB. This feature provides impact to your bass, but if not adjusted correctly, it
can be over used and cause damage to your subwoofers and amplifiers. It is best to slowly turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock
position unless listening at a low volume or a low recording quality as this can result in high distortion and possibly clipping.
Low Pass:
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the
Low Pass to 80Hz, the amplifier will not play frequencies above 80Hz but will play frequencies from 80Hz to the chosen Subsonic frequency.
Level Control Setup:
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit
volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input sensitivities properly to the
head unit output signal level.
It is important to match the amplifier
LEVEL
input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual.
If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier
LEVEL
input to 2 volts.
If you are not sure what the Radio output sensitivity is, follow these general guide lines:
Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to
the left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/subwoofer combo has reached its
maxx output in this application.
Q4.80 / Q4.150
General:
At this point you are ready to get more specific on the settings for your amplifier.
High Pass:
-When in HP-FULL operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12
o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz, the amplifier will not play frequencies below 100Hz but will play frequencies from 100Hz to the highest
frequency the amplifier is capable of reproducing.
-When in LP-BP operation, this setting acts as a low frequency cut off for your system reproduction aka Subsonic Filter. The point that you set it at cuts off any frequencies from reproduction beyond
this point. The 12 o’clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 60Hz, the amplifier will not play frequencies below 60Hz but will play frequencies from 60Hz to the
chosen Low Pass frequency
Filter Slope:
Selectable roll off for High Pass setting which is variable at 6dB for a steep cut, or 12dB for a smooth rolloff.
Bass Boost:
This setting is variable from 0-12dB. This feature provides impact to your bass, but if not adjusted correctly, it can be over used and cause damage to your speakers and amplifiers. It is best to slowly
turn this setting clockwise until the desired punch is felt. It is not recommended to exceed the 12 o’clock position unless listening at a low volume or a low recording quality as this can result in high
distortion and possibly clipping.
Bass Frequency:
Selects the frequency to amplify with the Bass Boost. Variable from 30Hz-80Hz. 11o’clock is 45Hz for reference.
Low Pass:
The Low Pass control acts as a ceiling and doesn’t allow frequencies to the right of the desired setting to be reproduced. Turning the potentiometer all the way to the right is a great starting point.
EXAMPLE: If you adjust the Low Pass to 120Hz, the amplifier will not play frequencies above 120Hz but will play frequencies from 120Hz to the chosen Hi Pass or Subsonic frequency.
Level Control Setup:
Ensure that the Level is turned completely to the left prior to turning the system on. Next you should insert a CD or cassette that you are familiar with to use as a reference, and turn the head unit
volume control to about 80% of its full setting. The system sound level will of course be very low, and the following procedures will help you to match the amplifier input sensitivities properly to the
head unit output signal level.
It is important to match the amplifier
LEVEL
input sensitivity to the Radio/CD output sensitivity. This can be located in the Radio/CD manual.
If the Radio/CD output sensitivity is 2 volts, then adjust the amplifier
LEVEL
input to 2 volts.
If you are not sure what the Radio output sensitivity is, follow these general guide lines:
Turn the level control up slowly, till you hear distortion, then back off a few degrees on the control. If at any point your amplifier goes into protection, you will need to turn the Level to
the left a bit and then try again. If you reach a point where the output does not increase, stop turning the Level control to the right as the amplifier/speaker combo has reached its maxx
output in this application.
Summary of Contents for Q4.150
Page 11: ...10 70Amps x 2...
