background image

12

©2020 Maxxsonics USA, Inc.

AMPLIFIER MOUNTING

AMPLIFIER PREPARATION AND MOUNTING (2013-2018 Models)

Before installing the dual amplifier plate with the amplifier(s) in position, you must prepare the mounting area 

in the vehicle to accept the plate.

NOTE

 - These instructions assume both amplifiers and all speakers are present in a full Stage 5 System. If 

not all components are present in your system, this makes upgrading much easier.

STEP 1 – LOOSEN STEERING COLUMN NUTS

Loosen the 16mm nuts that secure the steering column to the support frame shown in Figure 10-1a. These 

nuts are very hard to loosen. Be careful. Do not remove these steering column nuts, only loosen to create 

an 1/8 inch gap between the nut and the frame shown in Figure 10-1b. You will not re-tighten these nuts until 

the installation of the whole system is finalized, tested and the vehicle is ready for reassembly. 

STEP 2 – AMPLIFIER MOUNTING

Mount your amplifier(s) on the dual amplifier plate as shown in Figure 10-2 (below). This configuration is 

critical to make sure you can access your fine-tune adjustments for crossover and bass boost.

STEP 3 – MOUNTING PLATE INSTALLATION

With the amplifiers mounted to the plate, slide it into position with the double groove portion of the bracket 

sliding between the steering column support shown in 10.1b (above) and the 16mm nuts and washers. Do 

not tighten down yet. On the front edge, you will secure the plate with the 10mm bolt you removed from the 

dash pocket which will also hold the bracket then will ultimately support the new dash pocket with the source 

unit. The finished plate should look like Figure 10-3.

You will tighten the 16mm nuts and washers next to the steering column once reassembly of the vehicle 

begins. This allows easy removal of the amplifier plate for troubleshooting (if necessary).

NOTE

 - The dual amplifier harness is designed and laid out to perfectly connect power and speaker 

connections on the driver’s side of the amplifiers while the RCA audio connections are on the passenger 

side of the RZR. 

Figure 10-1a

Figure 10-1b

1/8” Gap

1/8” Gap

Figure 10-2

Figure 10-3

10mm

Summary of Contents for MBQR-STG5-2

































Reviews: