manualshive.com logo in svg

MB QUART MB QUART MBQR-STG2-RAD-2, Installation Manual, Page: 15 / 30

Share
Download
MB QUART MB QUART MBQR-STG2-RAD-2 Installation Manual Download Page 15

15

AMPLIFIER AND SPEAKER WIRING HARNESS CONNECTIONS 

With your amplifier(s) mounted, subwoofer installed and connected to the mono amplifier, you can now 

begin laying in the front/rear speaker harnesses and plugging in all the remaining connectors. While you are 

working on your system, we recommend covering the amplifiers to avoid scratching them or inadvertently 

hitting the adjustment dials with a wrench or screw driver.

STEP 1 – POWER AND SPEAKER CONNECTORS AT AMPLIFIERS

Plug in the power/ground connector of the two channel and the mono amplifiers 

respectively. At the same time, if you have (or will later install) optional illuminated 

MB Quart SR1-120RGB LED light rings, connect the red/black wires as well. Next, 

connect full range speaker connectors to the two channel amplifier. The optional 

subwoofer amplifier is prewired and can easily be added at a later date with the 

MBQR-SUB-2 package. See Figure 12-1 for the connection diagram.

STEP 2 – ROUTE FRONT SPEAKER HARNESS

Make sure your front left and front right kick panel 

harnesses are set into place. 

The left front harness for the kick panel should be 

routed down the left side of the steering column to 

the kick panel area.   

The right front harness for the kick panel needs 

to be routed over the subwoofer, not behind, and 

then to the kick panel area.

The kick panel pod installation will take place at a 

later step. For now, you are simply pre-wiring the 

harnesses to their respective areas. 

STEP 3 – ROUTE REAR SPEAKER HARNESS

Even if you aren’t currently installing rear 

speakers

, we recommend routing the rear 

speaker harness through the console area as 

shown in Figure 12-2. You can zip tie the harness 

in an accessible area for later use when you add 

rear speakers. 

NOTE 

– On a four seat RZR (4P RZR) you will need to include the 4P jumper to extend the rear speaker 

harness, past the rear seats and then to the rear pod area. See Figure 12-3 for connection.

Figure 12-1

Figure 12-2

Figure 12-3

Main Rear Speaker Harness 

Routing Through Console Area

Connection Points to Right Rear Speaker Wiring

Connection Points to Left Rear Speaker Wiring

HARNESS CONNECTIONS

Optional Mono Subwoofer Amplifier Shown

Summary of Contents for MB QUART MBQR-STG2-RAD-2































Reviews:

No comments