Mazda 2013 CX-5 Workshop Manual Download Page 206

Page: 206 / 223

FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041500800300.html[1/7/13 9:36:28 AM]

< Previous

Next >

2013 - CX-5 - Brakes

FRONT ABS WHEEL-SPEED SENSOR REMOVAL/INSTALLATION

1. Remove the mudguard. (See

MUDGUARD REMOVAL/INSTALLATION

2. Remove in the order indicated in the table.

3. Install in the reverse order of removal.

4. After installation, verify that there is no twisting in the front ABS wheel-speed sensor.

1Connector

2Bolt

3Front ABS wheel-speed sensor

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands