Mazda 2013 CX-5 Workshop Manual Download Page 139

Page: 139 / 223

BRAKE PEDAL REMOVAL/INSTALLATION

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id041100801200.html[1/7/13 9:32:56 AM]

Brake Pedal Removal Note

1. Move the power brake unit to the vehicle front where the power brake unit fork does not interfere with

the brake pedal arm.

2. Remove the brake pedal.

Brake Switch Installation Note

1. Inspect the brake pedal. (See

BRAKE PEDAL INSPECTION

2. With the brake pedal fully released, insert a new brake switch into the installation hole on the brake

pedal.

3. Secure the brake switch by turning it counterclockwise

45°

< Previous

Next >

Back to Top

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands