background image

3

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting installation. 

Read and follow the instructions provided with any tools listed 

here.

Tools needed:

Parts package is located in dryer drum. Check that all parts  

are included.

Parts needed: 

(Not supplied with dryer)

Check local codes. Check existing electrical supply and venting. 

See “Electrical Requirements” and “Venting Requirements” 

before purchasing parts.

Mobile home installations require metal exhuast system hardware 

available for purchase from the dealer from whom you purchased 

your dryer. For further information, please refer to the “Assistance 

or Service” section in your “Use and Care Guide.”

Optional Equipment: 

(Not supplied with dryer)

 

Refer to your “Use and Care Guide” for information about 

accessories available for your dryer.

Parts supplied (all models): 

Parts supplied (steam models): 

Flat-blade screwdriver

#2 Phillips screwdriver

Wire stripper (direct wire 

installations)

Tin snips (new vent 

installations)

1/4" nut driver 

(recommended)

Vent clamps

Adjustable wrench that 

opens to 1" (25 mm) or 

hex-head socket wrench 

Caulking gun and 

compound (for installing 

new exhaust vent)

Tape measure

Pliers

Level

Leveling legs (4)

“Y” connector

Short inlet hose

5' (1.52 m) inlet hose

Rubber washer

Summary of Contents for WED8200YW





















Reviews: