Maytag PD Questions Download Page 7 | Manualshive

Page: 7 / 14

Maytag PD Questions Download Page 7

Page 7

How to reset the machine when the display shows
0 minutes and will not reset?

This brief manual will answer the most commonly asked questions we receive for the Maytag
product range. If this does not answer your question, please phone our National After Sales
Department on 1300 RICHARD (742 427).

Q:

What does it mean when after the cycle has finished, I have opened the door,

but the display shows 0 minutes and does not reset?

1. This means that the lid switch or door switch (depending on model) is stuck. On washing

machines, it can get stuck if there is a build up of soap. To release the switch, simply clean
away the excess soap, or spray some CRC into that spot to release the button

Top Load Washer

Front Load Washer

Front Load Dryer

Switch Placement

The lid switch (or door switch) acts as a reset for the digital display. At the end of a cycle, this
button is normally released when the door is opened to remove clothing, and then depressed when
the door is closed. If that sequence does not happen, the digital display will not reset and will stay
showing 0 minutes left

Email:

[email protected]

Web:

www.richardjay.com.au

«
...
5
6
7
8
9
...
»

Summary of Contents for PD















Reviews:

No comments