background image

4

Maytag Co.

113062 - 17

Important Information ________________

IMPORTANT:

 A means of restraint must be used to prevent

straining of the gas supply when the dryer is moved.
An external means of power removal (disconnect device)
must be provided by the installer.

List of Acronyms _______________________

AWG

American Wire Gauge

DSI

Direct Spark Ignition

HVAC

Heating, Ventilating, and Air-Conditioning

in wc

Inches of Water Column

L.E.D.

Light Emitting Diode

L.P.

Liquid Propane

OSHA

Occupational Safety And Health Administration

UL

Underwriters Laboratory

“Caution: Label all wires prior to
disconnection when servicing controls.
Wiring errors can cause improper
operation.”
«Attention: Au moment de l’entretien des
commandes, étiquetez tous les fils avant de
les débrancher.  Des erreurs de câblage
peuvent entraîner un fonctionnement
inadéquat et dangereux.»

WARNING

The dryer must never be operated with any
of the back guards or service panels
removed.  Personal injury or fire could result.
The wiring diagram for the dryer is located
behind the front control panel on the right
side.

Table of Contents ________

Important Information ............................................... 5

Receiving and Handling ........................................... 5
Safety Precautions ................................................. 5

Specifications ............................................................ 7

Installation Procedures ............................................. 8

Unpacking/Setting Up ............................................. 8
Location of the Dryer ............................................... 8
Dryer Enclosure Requirements ............................... 9
Fresh Air Supply Requirements .............................. 9
Exhaust Requirements ........................................... 9
Electrical Information ............................................. 11
Gas Information .................................................... 12
Preparation for Operation ...................................... 14
Preoperational Test ............................................... 14
Shutdown Instructions .......................................... 15

Operating Instructions ............................................. 15

Starting the Dryer .................................................. 15

Service/Parts Information ...................................... 15

Service .................................................................. 15
Parts ..................................................................... 15

Warranty Information .............................................. 15

Returning Warranty Cards..................................... 15
Warranty ............................................................... 15

Routine Maintenance .............................................. 16

Cleaning ............................................................... 16
Adjustments ......................................................... 16
Lubrication ............................................................ 16

Dryer Data Label Information ................................ 17

Data Label Location .............................................. 17
Data Label ............................................................ 17

Summary of Contents for MLG32PDB


















Reviews: