Maytag MGT8720DH03 Installation Instructions Manual Download Page 6

6

Gas Supply Requirements

Observe all governing codes and ordinances.

IMPORTANT:

 This installation must conform with all local codes  

and ordinances. In the absence of local codes, installation must 

conform with American National Standard, National Fuel Gas 

Code ANSI Z223.1 - latest edition or CAN/CGA B149 - latest 

edition.

IMPORTANT:

 Leak testing of the range must be conducted 

according to the manufacturers instructions.

Type of Gas

Natural gas:

This range is factory set for use with Natural gas. See the “Gas 

Conversions” section. The model/serial/rating plate located 

behind the control panel has information on the types of gas that 

can be used. If the types of gas listed do not include the type of 

gas available, check with the local gas supplier.

LP gas conversion:

Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas 

specified on the model/serial/rating plate for use with a different 

gas without consulting the serving gas supplier. See the “Gas 

Conversions” section.

Gas Supply Line

 

Provide a gas supply line of 

3

/

4

" (1.9 cm) rigid pipe to the 

range location. A smaller size pipe on longer runs may result 

in insufficient gas supply. With LP gas, piping or tubing size 

can be 

1

/

2

" (1.3 cm) minimum. Usually, LP gas suppliers 

determine the size and materials used in the system.

NOTE: 

Pipe-joint compounds that resist the action of LP gas 

must be used. Do not use TEFLON

®†

 tape.

Flexible metal appliance connector:

 

If local codes permit, a new CSA design-certified, 4 to 5 ft 

(122 to 152.4 cm) long, 

1

/

2

" (1.3 cm) or 

3

/

4

" (1.9 cm) I.D., 

flexible metal appliance connector may be used for 

connecting range to the gas supply line.

 

1

/

2

" (1.3 cm) male pipe thread is needed for connection to 

the female pipe threads of the inlet to the appliance pressure 

regulator.

 

Do not kink or damage the flexible metal tubing when 

moving the range.

 

Must include a shut-off valve:
The supply line must be equipped with a manual shut-off 

valve. This valve should be located in the same room but 

external to the range opening, such as an adjacent cabinet. 

It should be in a location that allows ease of opening and 

closing. Do not block access to shut-off valve. The valve is 

for turning on or shutting off gas to the range.

Gas Pressure Regulator

The gas pressure regulator supplied with this range must be 

used. The inlet pressure to the regulator should be as follows for 

cproper operation:

Natural gas:

Minimum pressure: 5" WCP
Maximum pressure: 14" WCP

LP gas:

Minimum pressure: 11" WCP
Maximum pressure: 14" WCP
Contact local gas supplier if you are not sure about the inlet 

pressure.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure 

gas pressure does not exceed 14" (36 cm) water 

column. 
Examples of a qualified person include: 
licensed heating personnel, 

authorized gas company personnel, and

authorized service personnel.
Failure to do so can result in death, explosion, or fire.

A

B

C

A.  Gas supply line
B.  Shut-off valve open position
C.  To range

®

TEFLON is a registered trademark of Chemours

Summary of Contents for MGT8720DH03




















Reviews: