Maytag MGDB800VU - Bravos Steam Gas Dryer Installation Instructions Manual Download Page 6

6

block opening, screw removable conduit connector onto 
strain relief threads.  

 

A

 

A. Removable conduit connector
B. Hole below terminal block opening

C. Strain relief threads

Put direct wire cable through strain relief. Strain relief should 
have a tight fit with dryer cabinet and be in a horizontal 
position. Tighten strain relief screw against direct wire cable.    

4.

Now complete installation following instructions for your type 

 

of electrical connection:

4-wire

 (recommended)

3-wire

 (if 4-wire is not available)

 

If your home has:

And you will 

b

connecting to:

Go to Section

4-wire receptacle

 

(NEMA Type 14-30R)

A UL listed, 

 

120/240-volt 
minimum, 

 

30-amp, dryer 
power supply 
cord*

4-wire connection:

 

Power supply cord

4-wire direct

(127 mm)

5"

A fused 
disconnect or 
circuit breaker 
box*

4-wire connection:

 

Direct Wire

3-wire receptacle

 

(NEMA type 10-30R)

A UL listed, 

 

120/240-volt 
minimum, 

 

30-amp, dryer 
power supply 
cord*

3-wire connection:

 

Power supply cord

3-wire direct

(89 mm)

A fused 
disconnect or 
circuit breaker 
box*

3-wire connection:

 

Direct Wire

Electrical Connection Options

*If local codes do not permit connection of a cabinet-ground 

conductor to the neutral wire, see “Optional 3-wire connection” 
section.

4-wire connection: Power supply cord 

IMPORTANT: 

A 4-wire connection is required for mobile homes and 

where local codes do not permit use of 3-wire connections.

A

B

C

D

E

F

G

A. 4-wire receptacle (NEMA type 14-30R)
B. 4-prong plug

C. Ground prong
D. Neutral prong

E. Spade terminals with upturned ends
F. 3/4" (19 mm) UL listed strain relief

G. Ring terminals

1.

Remove center, silver-colored terminal block screw.

2.

Remove neutral ground wire from external ground conductor 
screw. Connect neutral ground wire and the neutral wire (white or 
center wire) of power supply cord under center, silver-colored 
terminal block screw. Tighten screw.

B

A

A. Neutral ground wire.
B. Center, silver-colored terminal block screw

C. External ground conductor screw - Dotted line shows position 

of NEUTRAL ground wire before being moved to center silver-
colored terminal block screw

D. Neutral wire (white or center wire) 

E. 3/4" (19 mm) UL listed strain relief

If your home has:

And you will 

b

connecting to:

Go to Section

Summary of Contents for MGDB800VU - Bravos Steam Gas Dryer

















Reviews: