9
9
9
9
9
9
IMPORTANT:
■
Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a colder than
recommended setting will not cool the compartments any
faster.
■
If the temperature is too warm or too cold in the refrigerator
or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
■
The preset temperatures should be correct for normal
household usage. The controls are set correctly when milk
or juice is as cold as you like and when ice cream is firm.
■
Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
To view and adjust the set points, press and hold the TEMP
button for 3 seconds. When Adjust mode is activated, adjusting
information will appear on the display screen.
NOTE: To view Celsius temperatures, press the Light button when
Adjust mode is activated. To return the display setting to
Fahrenheit, press LIGHT again.
■
When Adjust mode is activated, the display screen shows
the refrigerator set point and “FRIDGE” appears.
■
Press LOCK to raise the set point, or press PowerCold to
lower the set point.
■
When you have finished viewing (and adjusting if desired) the
refrigerator set point, press TEMP to change the display to
show the freezer set point. When the zone has been changed,
“FREEZER” appears on the display screen.
■
Press LOCK to raise the set point, or press POWERCOLD to
lower the set point.
■
When you have finished viewing (and adjusting if desired) both
the refrigerator and freezer set points, press FILTER to save
the settings.
NOTE: To exit without saving changes, press ICE TYPE at
any time while in Adjust mode or allow about 60 seconds
of inactivity and adjust mode will turn off automatically.
When adjusting temperature set points, use the following chart
as a guide.
The set-point range for the refrigerator is 33°F to 45°F (0°C to
7°C). The set-point range for the freezer is -5°F to 5°F (-21°C to
-15°C).
Cooling On/Off
Your refrigerator and freezer will not cool when cooling is
turned off.
■
To turn cooling off, press and hold the Lock and Filter buttons
at the same time for 3 seconds. When cooling is OFF,
“COOLING OFF” will appear on the display screen.
IMPORTANT: To avoid unintentionally locking the dispenser
or changing other settings, be sure to press both buttons at
exactly the same time.
Press and hold LOCK and FILTER for 3 seconds again to turn
cooling back on.
Additional Features
POWERCOLD
The POWERCOLD feature assists with periods of high
refrigerator use, full grocery loads, or temporarily warm room
temperatures.
■
Press POWERCOLD to set the freezer and refrigerator to the
lowest temperature setting. When the feature is ON, the
PowerCold icon will appear on the dispenser display screen.
The PowerCold feature will remain ON for 24 hours unless
manually turned off.
■
To manually turn off the PowerCold feature, press
POWERCOLD again or adjust the refrigerator temperature set
point. The PowerCold icon will disappear when the feature is
OFF.
NOTE: Setting the freezer to a colder temperature may make
some foods, such as ice cream, harder.
Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the refrigerator
or freezer door is open for 5 minutes and the product cooling is
turned on. The alarm will repeat every 2 minutes. Close both
doors to turn it off. The feature then resets and will reactivate
when either door is left open again for 5 minutes.
NOTE: To mute the audible alarm while keeping the doors open,
such as while cleaning the inside of the refrigerator, press any
button on the control panel. The alarm sound will be temporarily
turned off, but the Door Ajar icon will still be displayed on the
dispenser control panel.
CONDITION:
TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold
REFRIGERATOR Setting
1° higher
REFRIGERATOR too warm
REFRIGERATOR Setting
1° lower
FREEZER too cold
FREEZER Setting
1° higher
FREEZER too warm/
too little ice
FREEZER Setting
1° lower
PowerCold
A. Press LOCK and FILTER RESET at the same time.
A
PowerCold
