manualshive.com logo in svg

Maytag MER6875BA Series, Technical Information, Page: 4 / 11

Share
Download
Maytag MER6875BA Series Technical Information Download Page 4

Control Testing Procedures 

 

!

WARNING

 

To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless  
testing requires power. 

16027361 4  July 

2006 

 

 

©2006 Maytag Services 

 

Control Feature 

Procedure 

Results 

H2.5 Oven 

Temperature 

Adjustment  
(Upper Oven) 

Press 

Upper Bake 

pad. 

Enter 

550

 on the digit-pad. 

Immediately press and hold 

Upper

 

Bake

 pad for 3 to 

5 seconds. 
Oven can be adjusted from -35 to +35 degrees in 5-
degree increments by pressing 

Autoset

 pad. To 

avoid over adjusting the oven, move temperature 5 
degrees each time. Wait 4 seconds for the data entry 
timer to expire to accept the change. Temperature 
adjustment will be retained even through a power 
failure

.

 

While increasing or decreasing oven 
temperature, oven self-cleaning 
temperature is not affected. 

H2.5 Oven 

Temperature 

Adjustment  
(Lower Oven) 

Press 

Lower Bake 

pad. 

Enter 

550

 on the digit-pad. 

Immediately press and hold 

Lower

 

Bake

 pad for 3 to 

5 seconds. 
Oven can be adjusted from -35 to +35 degrees in 5-
degree increments by pressing 

Autoset

 pad. To 

avoid over adjusting the oven, move temperature 5 
degrees each time. Wait 4 seconds for the data entry 
timer to expire to accept the change. Temperature 
adjustment will be retained even through a power 
failure

.

 

While increasing or decreasing oven 
temperature, oven self-cleaning 
temperature is not affected. 

H2.5 Temperature 

Display 

Press and hold 

Upper

 

Cancel

 and 

Upper

 

Bake

 

pads for 3 to 5 seconds. 

Indicates °F or °C on the display. 

H2.5 Clock 

Display  Press and hold 

Upper

 

Cancel

 and 

Clock

 pads for 3 

to 5 seconds. 

Turns clock display on or off. 

H2.5 24-Hour 

Clock  Press and hold 

Upper

 

Cancel

 and 

Favorite

 pads for 

3 to 5 seconds. 

Displays either 12-hour or 24-hour 
time format. 

H2.5 Factory 

Default Press and hold 

Upper

 

Cancel

 and 

Upper

 

Keep 

Warm

 pads for 3 to 5 seconds. 

Resets control to factory settings. 

H2.5 

12-Hour Off 

Control automatically cancels cooking operation and 
removes all relay drives 12 hours after the last pad 
touch. 

See Sabbath mode to disable. 

H2.5 Sabbath 

Mode  Hold 

Clock

 pad for 3 to 5 seconds to activate 

Sabbath mode. 
 
Hold 

Clock

 pad

 

for 3 to 5 seconds to disable 

Sabbath mode. 

"SAbbAth" displays for 5 seconds, 
then changes to "SAb" (displays in 
Temp area). 
All pad inputs are disabled except 

CANCEL

 and 

CLOCK

 pads. 

This mode disables the normal 12-
hour shutoff to allow operation of the 
bake mode for a maximum of 72 
hours. 

Summary of Contents for MER6875BA Series












Reviews:

No comments