background image

2

16026784

© 2005 Maytag Services

Pride and workmanship go into every product to provide our customers with quality products.  It is possible, however,
that during its lifetime a product may require service.  Products should be serviced only by a qualified service
technician who is familiar with the safety procedures required in the repair and who is equipped with the proper tools,
parts, testing instruments and the appropriate service information.  

IT IS THE TECHNICIANS RESPONSIBILITY TO

REVIEW ALL APPROPRIATE SERVICE INFORMATION BEFORE BEGINNING REPAIRS.

Important Notices for Servicers and Consumers

!

WARNING

To avoid risk of severe personal injury or death, disconnect power before working/servicing on appliance to avoid
electrical shock.

To locate an authorized servicer, please consult your telephone book or the dealer from whom you purchased this
product.  For further assistance, please contact:

Customer Service Support Center

CAIR Center

Web Site

Telephone Number

WWW.AMANA.COM ................................................ 1-800-843-0304
WWW.MAYTAG.COM ............................................. 1-800-688-9900

CAIR Center  in Canada .......................................... 1-800-688-2002
Amana Canada Product ........................................... 1-800-587-2002

Recognize Safety Symbols, Words, and Labels

DANGER

!

DANGER—

Immediate hazards which 

WILL

 result in severe personal injury or death.

WARNING

!

WARNING—

Hazards or unsafe practices which 

COULD

 result in severe personal injury or death.

CAUTION

!

CAUTION—

Hazards or unsafe practices which 

COULD

 result in minor personal injury, product or property

damage.

Important Information

Summary of Contents for MER5551BA - 30'' Electric Range
























































Reviews: