background image

Retain This Manual In A Safe Place For Future Reference

This product embodies advanced concepts in engineering, design, and safety.  If this product is properly maintained, it will
provide many years of safe, efficient, and trouble-free operation.

ONLY qualified technicians should service this equipment.

OBSERVE

 

ALL

 

SAFETY

 

PRECAUTIONS

 displayed on the equipment or specified in the installation manual included with

the dryer.

The following “

FOR YOUR SAFETY

” caution 

must be

 posted near the dryer in a prominent location.

“IMPORTANT NOTE TO PURCHASER”

Information 

must be 

obtained from your local gas supplier on the instructions

to be followed if the user smells gas.  These instructions 

must be 

posted in a

prominent location near the dryer.

FOR YOUR SAFETY

Do not store or use gasoline or
other flammable vapors and
liquids in the vicinity of this or
any other appliance.

POUR VOTRE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables  à proximité de cet
appareil ou de tout autre appareil.

We have tried to make this manual as complete as possible and hope you will find it useful.  

The manufacturer 

 reserves the

right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to
change or discontinue models.  The illustrations included 

in this manual may not depict your particular dryer 

exactly

.

Important

For your convenience, log the following information:

DATE OF PURCHASE ________________________________ MODEL NO. __________________________________________

DEALER’S NAME __________________________________________________________________________________________

Serial Number(s)

________________________________________________________________________________________

________________________________________________________________________________________

________________________________________________________________________________________

For replacement parts, contact the dealer from which the dryer was purchased or contact:

Maytag Co.

403 West Fourth Street North

Newton, Iowa 50208

(641) 787-7000

Summary of Contents for MDG30V





















































Reviews: