background image

2

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING: 

When using the dishwasher, follow basic precautions, including the following:

 

Read all instructions before using the dishwasher.
Use the dishwasher only for its intended function.
Use only detergents or rinse agents recommended for use in a

dishwasher, and keep them out of the reach of children.
When loading items to be washed:
1) Locate sharp items so that they are not likely to damage the

door seal; and

2) Load sharp knives with the handles up to reduce the risk of

cut-type injuries.

Do not wash plastic items unless they are marked  “dishwasher

safe” or the equivalent. For plastic items not so marked, check

the manufacturer's recommendations.
Do not touch the heating element during or immediately after use.
Do not operate the dishwasher unless all enclosure panels are

properly in place.

Do not tamper with controls.
Do not abuse, sit on, or stand on the door, lid, or dish racks of

the dishwasher.

To reduce the risk of injury, do not allow children to play in or

on the dishwasher.
Under certain conditions, hydrogen gas may be produced in a

hot water system that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system

has not been used for such a period, before using the

dishwasher turn on all hot water faucets and let the water flow

from each for several minutes. This will release any

accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.
Remove the door or lid to the washing compartment

when removing an old dishwasher from service or

discarding it.

Do not use replacement parts that have not been recommended 

by the manufacturer (e.g. parts made at home using a 3D printer).

GROUNDING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

■  

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a 

malfunction or breakdown, grounding will reduce the risk of 

electric shock by providing a path of least resistance for 

electric current. The dishwasher is equipped with a cord 

having an equipment-grounding conductor and a grounding 

plug. The plug must be plugged into an appropriate outlet 

that is installed and grounded in accordance with all local 

codes and ordinances.

WARNING:

 Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. 

Check with a qualified electrician or service representative if 

you are in doubt whether the dishwasher is properly 

grounded. Do not modify the plug provided with the 

dishwasher; if it will not fit the outlet, have a proper outlet 

installed by a qualified electrician.

■  

For a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal, 

permanent wiring system, or an equipment-grounding 

conductor must be run with the circuit conductors and 

connected to the equipment-grounding terminal or lead on 

the dishwasher.

Summary of Contents for MDB9959SKZ




























Reviews: