Maytag MAT20MNTKW Instructions Manual Download Page 4

4

n

   Do not allow children to play on, in, or with the washer. 

Close supervision of children is necessary when the washer 
is used near children. 

n

   Before the washer is removed from service  

or discarded, remove the door or lid.

n

   Do not reach into the washer if the basket, tub, or agitator 

is moving. 

n

   Water Heater set to 49°C (120°F).

n

  

Do not install or store the washer where it will be exposed 
to the weather.

n

   Do not tamper with controls.

n

   After installation, access to mains plug must be maintained 

at all times in order to ensure immediate deactivation of the 
washer in case of emergency.

n

  

Do not repair or replace any part of the washer or attempt 
any servicing unless specifically recommended in this 
manual. You must also understand these instructions and 
have the skills to carry them out.

SAVE THESE INSTRUCTIONS

n

   See “Electrical Requirements” for grounding instructions.

n

   Water pressure of 138–690 kPa (20–100 psi) 

is needed for operation of the washer.

n

   Use new hoses supplied with the washer.  

Do not reuse old hoses.

n

   If the supply cord is damaged, it must be replaced by the 

manufacturer, its service agent, or similarly qualified persons 
in order  
to avoid a hazard.

n

   IEC capacity: 10.5 kg.

n

   Washer installation and service must be performed by a 

Maytag authorized service person.

n

   Do not use an extension cord or an electrical portable outlet 

device.

n  

Only authorized spare parts shall be used in the event of     

 failure.

These units are sold in multiple regions with different 
requirements. Below are a few of the valid forms of measure 
posted on this product’s capacity:

Dry Linen Capacity:

 A weight measure that reflects a minimum 

threshold for dry volume capacity that is needed for import tariff 
purposes.

IEC Capacity:

 A capacity measure that represents the 

maximum capacity of dry linens and textiles which the 
manufacturer declares can be treated in a single cycle.

SPECIFICATIONS

Dry Linen Capacity

10.5 kg (23 lb)

IEC Capacity

10.5 kg (23 lb)

Sound Level

Lpa: 58 db(A) (Kpa +/- 10 db(A))

Summary of Contents for MAT20MNTKW

















Reviews: