Maytag MAT20MNTKW Instructions Manual Download Page 1

W11591528A

INSTRUCTIONS 

FOR

 OWNERS

(

ORIgINal

 

INSTRUCTIONS

)

C

ommerCial

 W

asher

 

Model

: maT20mNTKW

www.maytagcommerciallaundry.com

4

IMPORTANT SAFETY INSTRUCTIONS

precautions, including the following:

WARNING:

 

Read all instructions before using the dryer.
Keep a minimum clearance of 100 mm (4 in.) between the
rear of the dryer and any wall. 

 

The operation of this appliance may affect the operation of

other types of appliances which take their air supply for safe

combustion from the same room. There has to be adequate

ventilation to replace exhausted air and thus avoid the

back-flow of gases into the room from appliances burning

other fuels, including open fires, when operating the tumble
dryer. If in doubt, consult the appliance manufacturers.   
Do not obstruct the air supply to the dryer (see Installation
Instructions for minimum clearances). 
Do not place items exposed to cooking oils in your dryer.

Oil-affected items can ignite spontaneously, especially when

exposed to heat sources such as in a tumble dryer. The

items become warm causing an oxidation reaction in the oil.

Oxidation creates heat. If the heat cannot escape, the items

can become hot enough to catch fire. Piling, stacking or

storing oil-affected items can prevent heat from escaping
and so create a fire hazard.   
If it is unavoidable to dry in the dryer items that have been

soiled with substances such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes and wax

removers, or that have been contaminated by hair care

products, should be washed in hot water with an extra

amount of detergent before being dried in the dryer. These

items may give off vapours that could ignite or explode. Such
washing will reduce, but not eliminate, the hazard.   
This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instructions concerning

use of the appliance by persons responsible for their safety.
Children should be supervised to ensure that they do not

play with the appliance. 
The dryer should not be used if industrial chemicals have

been used for cleaning. 

Before the dryer is removed from service or discarded,
remove the doors to the drying compartment. 
Do not reach into the dryer if the drum is moving. A door

switch is fitted for your safety. 
Do not install or store the dryer where it will be exposed
to the weather. 
Do not tamper with controls.
Do not continue to use this appliance if it appears to be

faulty. 
Do not repair or replace any part of the dryer or attempt

any maintenance unless specifically recommended in this

Use and Care Guide. Repairs and servicing should only

be carried out by competent service personnel.  
Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product. Follow their instructions. 
Clean dryer lint screen before or after each load. Do not

operate dryer without lint screen in place. 
Keep area around the exhaust and inlet openings and

adjacent surrounding areas free from the accumulation of
lint, dust, and dirt. 
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel. 
See Installation Instructions for earthing instructions.
Do not dry unwashed items in this dryer.

Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes or

pillows fitted with foam rubber pads must only be dried
on a clothesline.  

SAVE THESE INSTRUCTIONS

WARNING: 

Never stop a tumble dryer cycle before the

end of the drying cycle unless all items are quickly removed
and spread out so that the heat is dissipated.  

To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic

The final part of a tumble dryer cycle occurs without heat

(cool down cycle) to ensure that the items are left at a
temperature that ensures the items will not be damaged. 

If the supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.  

Summary of Contents for MAT20MNTKW

















Reviews: