background image

 

 

 

 

 

 

 

 

Page 2 of 34  

 

INTRODUCTION 

 

WARNING: Disconnect power from electrical source before  

 

 

 

 

  performing this procedure. 

 

Please read and familiarize yourself with these instructions in their entirety before proceeding.  The 
procedure below shows the step by step instructions to convert a Dixie-Narco Beverage Max Vender 
(DN55## and  DN35## Series) to an Entray Vender.  These instructions 

do not apply

 to any models other 

than the DN5500 Series (e.g. DN2145, DN2054).  The Beverage Max series is an all drink (can and bottle) 
machine, while the Entray is a combination snack and drink machine.   The Entray shelves may replace 
drink shelves in only shelf locations A, B, and C; and must start with shelf location A and progress to B and 
C (top to bottom) if less than 3 Entray shelves are to be used. 

 

TOOLS NEEDED 

 

1/4” Socket Wrench 

 

Philips Screw Driver 

 

Scissors 

 

EPROM Puller 

 

Static Discharge Strap 

 

ORDER 

 
 

Note: Kits do not include helix.  Please order helix as needed. 

 

Part Description 

Part # 

Part Description 

Part # 

28 Count Right Hand 

801,701,35x.x1 

10 Count Right Hand 

801,701,39x.x1 

28 Count Left Hand 

801,701,36x.x1 

10 Count Left Hand 

801,701,41x.x1 

20 Count Right Hand 

801,701,48x.x1 

9 Count Right Hand 

801,701,42x.x1 

20 Count Left Hand 

801,701,49x.x1 

9 Count Left Hand 

801,701,43x.x1 

17 Count Right Hand 

801,701,26x.x1 

8 Count Right Hand 

801,701,44x.x1 

17 Count Left Hand 

801,701,27x.x1 

8 Count Left Hand 

801,701,45x.x1 

13 Count Right Hand 

801,701,37x.x1 

7 Count Right Hand 

801,701,31x.x1 

13 Count Left Hand 

801,701,38x.x1 

7 Count Left Hand 

801,701,32x.x1 

11 Count Right Hand 

801,701,28x.x1 

6 Count Right Hand 

801,701,46x.x1 

11 Count Left Hand 

801,701,29x.x1 

6 Count Left Hand 

801,701,47x.x1 

 

 

 

 

 

 

 

 

 
 

PART DESCRIPTION 

DN55## KIT 

DN35## KIT 

Tray Assembly 5 Column 5 – 11 

645,010,00x.x4 

NA 

Tray Assembly 5 Column 5 – 11 No Vend Sensor Kit 

645,010,20x.x4 

NA 

Tray Assembly 3 Column 3 - 11 

NA 

645,010,10x.x4 

Tray Assembly 3 Column 3 – 11 No Vend Sensor Kit 

NA 

645,010,30x.x4 

Summary of Contents for Dixie-Narco Beverage Max DN35 Series



































Reviews: