Maytag C3 User Manual Download Page 32

32

FULL ONE YEAR WARRANTY

For one year from the date of original retail purchase, any part which fails in normal home use will be repaired
or replaced free of charge.

If a leak occurs in the tank, a new water heater of the closest capacity and quality then available, will be
replaced free of charge.

The warranty of the replacement is the balance of the original water heater’s warranty.

LIMITED PARTS WARRANTY

After the first year and through the sixth year from the date of original retail purchase, any parts which fail due
to a defect in materials or workmanship, will be replaced or repaired free of charge for the part itself, with the
owner paying all other costs, including labor, mileage and transportation.

If the water heater is subjected to commercial, institutional, industrial or non-residential use, the above
warranty coverage for parts that are proved to be defective in material or workmanship is effective for one year
from the date of the original retail purchase.

The warranty of the replacement is the balance of the original water heater’s warranty, or twelve months from
the date of the part(s) purchase, whichever comes first.

This warranty is limited to the original owner of the water heater.

LIMITED TANK WARRANTY AGAINST LEAKS

After the first year and through the sixth year from the date of original retail purchase, if a leak occurs in the
tank, a new water heater of the closest capacity and quality then available, will be replaced free of charge for
the water heater, with the owner paying all other costs, including labor, mileage and transportation.

If the water heater is subjected to commercial, institutional, industrial or non-residential use, the above
warranty coverage for the tanks that are proved to be defective in material or workmanship is effective for two
years from the date of the original retail purchase.

The warranty of the replacement is the balance of the original water heater’s warranty.

Please note: The full and limited warranty applies only while this water heater is used in the United States of
America.

This warranty is limited to the original owner of the water heater.

TO RECEIVE WARRANTY SERVICE

To locate an authorized service company in your area contact the Maytag dealer from whom your appliance
was purchased; or call Maytag Customer Service at the number listed below. Should you not receive satisfactory
warranty service, please call or write:

Maytag Customer Service
P.O. Box 2370
Cleveland, TN 37320-2370
U.S.A. 1-800-788-8899

When contacting Maytag Customer Service be sure to provide the model and serial number of your appliance,
the name and address of the dealer from whom you purchased the appliance and the date of purchase.

MAYTAG WATER HEATERS ARE MANUFACTURED AND THIS WARRANTY IS PROVIDED BY STATE
INDUSTRIES, INC., ASHLAND CITY, TN. MAYTAG IS A TRADEMARK OF THE MAYTAG CORPORATION AND IS
USED UNDER LICENSE TO STATE INDUSTRIES, INC.

WARRANTY

Summary of Contents for C3

































Reviews: