MayPole MP7429 Instruction Manual Download Page 6

DDDDDDD

DDDD

ww

w.maypole.ltd.uk

 

MAMMMMMMMMM

pole.ltd.uk

 

www.maypole.ltd.uk

 

 

 

 

FLASHLIGHT

 

 

 

This product features a LED flashlight which is activated by pressing and holding the ON/OFF switch on the side of the 
unit for three seconds.  The flashlight can be deactivated by pressing and holding the same button for a further 3 
seconds 
 

TECHNICAL SPECIFICATIONS 

 

 
Product dimensions (mm) 

 

139 x 75 x 15 

Weight (g) 

 

 

 

200 

Battery capacity (mAh)   

 

6000 

Output   

 

 

 

5V

2A; 12V jump start 

Input   

 

 

 

15V

1A; 5V

2A 

Time required for full charge 

 

Approximately 2 hours 

Starting current  

 

 

150A 

Peak current 

 

 

 

300A 

Operating temperature   

 

-

20˚C ~ 60˚C

 

 

FREQUENTLY ASKED QUESTIONS 

 

 
Q. 

How do I turn off the product? 

A. 

The device will automatically switch off once charging is complete or no USB devices are connected. 

 
Q. 

How long does it take to fully cahrge the battery within the unit? 

A. 

Approximately two hours if charged via a 15V 1A supply or 5V 2A supply. 

 
Q. 

How many times can the product fully charge a mobile phone before the internal battery requires recharge? 

A. 

This is heavilly dependant on the specific mobile phone being charged; as an example, an iPhone 4 can be fully 
charged three times. 

 
Q. 

How long will the product require to fully charge a mobile phone? 

A. 

Approximatly one hour. 

 
Q. 

How many times can the product jump start a vehilce before the internal battery requires recharge? 

A. 

This  is  heavilly  dependant  upon  the  condition  of  the  vehicle  battery  and  its  state  of  charge  prior  to  jump 
starting; the device could successfully jump start a vehicle two or three times before a recharge is required.  

 
Q. 

What is the anticipated life-span of the product? 

A. 

Approximately 3-5 years under normal conditions and use. 

 
Q. 

Once fully charged, how long with the internal battery retain its charge before a recharge is necessary? 

A. 

It is recommended the product is charged once every three months if not used. 

 
Q. 

What vehicle types can I jump start using this device? 

A. 

The unit can be used on most petrol engine vehicles with an engine size up to three liters.  

 
Q. 

How should this unit be disposed of at the end of its useful life? 

A. 

The unit contains hazardous constituents that should be disposed of at local authority registered waste 
recycling center or a battery collection point. 

 

10

 

12

 

Summary of Contents for MP7429








Reviews: