background image

3

ENG

Please read and observe all sections of this Operating Manual. Thorough attention should be paid to the safety, ser-

vice and maintenance instructions and to the training information at all times. Please ensure that anyone using the 

training device is equally familiar with these instructions and that they follow them. Keep this manual in a safe place 

for further reference on information, maintenance and cleaning and for details on ordering of spare parts.

It is very important strictly to follow the service and maintenance and safety instructions contained in this Manual. 

This training device is only to be used for its intended purpose. This means it is to be used for body workouts by adults only.

If this equipment is used for any other purposes than intended, there is a possible risk of accident, damage to health or damage 

to the training device. The Distributor cannot be held responsible for damages caused by improper use. 

Training Environment

 

Select a suitable space for your training device to provide an optimum amount of free space and highest level of safety.

 

Ensure that the load capacity of the floor or ground of the chosen area is sufficient for the load.

 

Make sure that the area is well ventilated and that an optimum amount of oxygen is available during training. Avoid 

draughts.

 

It is not permitted to locate your training device in busy areas or areas near to main walkways (emergency exits, doors or 

passageways)

 

Your training device is not suitable for outside use and so storage and training can only take place in a temperate, dry 

clean room.

 

Operation and storage of your training device in wet areas such as in swimming pools, saunas etc. is not possible. 

 

Make sure that your training device is kept on flat, hard and clean ground both in operation and at standstill. Any uneven 

surfaces must be removed or made good.

 

It is recommended that a floor covering (carpet, mat, etc.) should be placed under the device to protect damageable floors 

such as wood, laminates, floor tiles etc. We recommend placing MAXXUS® floor protection mats permanently under the 

device. Please ensure that these mats cannot slip or slide. 

 

Do not put this training device on pale or white coloured carpets or rugs as the feet of the device may leave marks. 

 

Make sure that your training device is kept out of contact with hot items and is kept at a safe distance from any sources of 

heat e.g. central heating, hot stoves, furnaces, ovens or open fires.

Personal Safety Instructions for Training

 

You should go to the doctor and have a health check before you start working out.

 

Stop training immediately if you feel physically unwell or are experiencing any breathing difficulties.

 

Always start your training session at a low workload increasing it slowly but steadily throughout. Reduce the workload 

again towards the end of your training session.  

 

Suitable sports shoes and clothes should always be worn during training sessions. Make sure that loose clothes do not 

get caught up in any moving parts of the device.

 

Your training device is only to be used by one person at a time. 

 

Check each time before a training session to see if your device is in perfect condition. Never use your training device if it is 

faulty or defective.

 

You are only permitted to carry out repairs to the device yourself after having contacted our Service Department and on 

receipt of explicit permission to do so. Only original spare parts may be used at any time. 

 

Improper repairs or structural modifications (attachment of non-permissible parts, removal of original parts etc) are not 

permitted. This can impair the technical safety of the device and cause risk for the user.

 

Your training device must be cleaned after each use. Remove all dirt including body sweat or any other liquids. 

 

Your training device is not suitable for use by children.

 

Third parties, especially children and animals, must be kept at an appropriate safety distance during training.

 

Check before each training session if there are any items underneath the training device and remove them without fail. 

Never use the training device when items are underneath it. 

 

Do not allow children to use your training device as a toy or climbing frame at any time. 

 

Ensure that no body parts of your own or of third parties ever come into contact with any of the moving mechanisms.

 

Warn anyone present at your training sessions, especially children, of the possible risk. This applies to the areas where 

weight plates, weight stacks or barbells.

 

Check all parts at regular intervals (at least once a month) and make sure that all screws and nuts are tightened properly.

The construction of this training device is based on state of the art technology and highest modern technical safety standards.  

This training device is to be used by adults only!

Extreme misuse and/or unplanned training can cause damage to your health!

Any manipulation of or interference with the device can cause damage to the device and be a danger to people.

If you have any questions or queries contact your specialist dealer or the MAXXUS Service Team and they will be pleased to 

help you further.

    Safety Instructions  

Summary of Contents for GRAVITY PRO 2.0























Reviews: