Maxx Ice MIM150N Service, Installation, And Instruction Manual Download Page 14

Cleaning and Maintenance

If the ice maker is left unused for a long time, before the next use it must 

be thoroughly cleaned  Follow carefully any instructions provided for 

cleaning or use of sanitizing solution  Do not leave any solution inside the 

ice maker after cleaning 

Periodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The 

maintenance intervals listed are based on normal conditions  You may want to shorten the intervals if 
you have pets or there are other special considerations 

WHAT SHOULDN’T BE DONE

Never keep anything in the ice storage bin other than ice: objects like wine and beer bottles are not 
only unsanitary, but the labels may slip off and plug up the drain 

WHAT SHOULD BE KEPT CLEAN

There are 4 things to keep clean:
1  The exterior                                                 
2  The interior                                             
3  Water distribution tube
4  The ice-making system cleaning

Before proceeding with cleaning and maintenance operations, make 

sure the power line of the unit is disconnected and the water line is shot 

off  (EXCEPTION: Cleaning of ice-making system)

EXTERIOR CLEANING

The door and cabinet may be cleaned with a mild detergent and warm water solution such as 1 oz of 
dishwashing liquid mixed with 2 gallons of warm water  Do not use solvent-based or abrasive cleaners  
Use a soft sponge and rinse with clean water  Wipe with a soft clean towel to prevent water spotting  
Clean stainless steel with a cloth dampened with a mild detergent and warm water solution  Never use 
an abrasive cleaning agent 

INTERIOR CLEANING

The ice storage bin should be sanitized occasionally  Clean the water tank before the ice cube machine 

is used for the first time and reused after stopping for an extended period of time. It is usually convenient 

to sanitize the trough after the ice-making system has been cleaned and the ice storage bin is empty 

1  Disconnect power to the unit 

2.  Open the door. 

 

3   Using a sanitizing solution made of 1 ounce of household bleach and 2 gallons of hot water (95º to 

115ºF), wipe down the water tank and the inside of the ice storage bin with a clean cloth  To clean 

hard-to-reach corners, apply the sanitizing solution with a spray bottle 

4  Rinse thoroughly with clear water  This completes the routine interior cleaning of the unit 
5  Reconnect the power 

The ice scoop should be washed regularly  W

  ash it just like any other food container 

DANGER

WARNING

CAUTION

DANGER

WARNING

CAUTION

13

 

6  

 

DO NOT use solvent-based cleaning agents or abrasives on the interior  

These cleaners may transmit taste to the ice cubes, or damage or discolor 

the interior 

WARNING

CAUTION

Summary of Contents for MIM150N





















Reviews: