manualshive.com logo in svg

Maxtor DiamondMax 21 STM3160215AS, Product Manual, Page: 35 / 56

Share
Download
Maxtor DiamondMax 21 STM3160215AS Product Manual Download Page 35

DiamondMax 21 Serial ATA Product Manual, Rev. C

29

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution: 

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal 

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire 
installation procedure.

• Handle the drive by its edges or frame 

only

.

• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids 

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are 
used to seal out dirt and contamination.

Summary of Contents for DiamondMax 21 STM3160215AS

























































Reviews:

No comments