Maxtor DiamondMax 20 STM3160212A Product Manual Download Page 18

10

DiamondMax 20 PATA Product Manual, Rev. A

Table 4: 

Drive specifications summary

 for the 80 and 40 Gbyte models

Drive specification

STM3802110A

STM3402111A

Formatted Gbytes (512 bytes/sector)*

80

40

Guaranteed sectors

156,301,488

78,165,360

Bytes per sector

512

Default sectors per track

63

Default read/write heads

16

Default cylinders

16,383

Recording density

840.0 kbits/in max

611.5 kbits/in max

Track density

141.5 ktracks/in avg

103.9 ktracks/in avg

Areal density

119.0 Gbits/in

avg

63..53 Gbits/in

avg

Spindle speed

7,200 RPM

Internal data transfer rate

867.2 Mbits/sec max

Sustained data transfer rate OD

83.0 Mbytes/sec max

69.4 Mbytes/sec max

I/O data-transfer rate

100 Mbytes/sec max

ATA data-transfer modes supported

PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–5

Cache buffer

2 Mbytes

Height (max)

26.1 mm (1.028 inches)

Width (max)

101.6 mm (4.000 inches) +/- 0.010 inches

Length (max)

146.99 mm (5.787 inches)

Weight (max)

580 grams (1.28 lb.)

525 grams (1.16 lb.)

Average latency

4.16 msec

Power-on to ready (max)

<10.0 sec 

Standby to ready (max)

<10.0 sec

Track-to-track seek time

<0.8 msec typical (read),  <1.0 msec typical (write)

Average seek, read (typical)

<11.0 msec

Average seek, write (typical)

<12.0 msec

Startup current (typical) 12V (peak)

2.8 amps

Voltage tolerance (including noise)

5V ± 5%
12V ± 10%

Ambient temperature

0° to 60°C (operating)
–40° to 70°C (nonoperating)

Temperature gradient

20°C per hour max (operating)
30°C per hour max (nonoperating)

Relative humidity

5% to 90% (operating)
5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature

37.7°C max (operating)
40.0°C max (nonoperating)

Altitude, operating

–60.96 m to 3,048 m
(–200 ft. to 10,000+ ft.)

Altitude, nonoperating 
(below mean sea level, max)

–60.96 m to 12,192 m
(–200 ft. to 40,000+ ft.)

Operational Shock

63 G max at 2 msec

Non-Operational Shock

350 G max at 2 msec

Vibration, operating

5–22 Hz: 0.25 G, Limited displacement
22–350 Hz: 0.50 G
350–500 Hz:: 0.25 G

Summary of Contents for DiamondMax 20 STM3160212A

























































Reviews: