Maxton EMV10 Manual Download Page 90

Page: 90 / 102

1728 Orbit Way - Minden, Nevada 89423 P: 775-782-1700 F: 775-782-1701 [email protected] www.maxtonvalve.com

\\SERVER\CATALOG 2019\2019 Catalog Rev 2

BV3-4

Maxton Bleed Port's are machined parts with black oxide finish designed to aid in the bleeding of air from the

jack during installation, oil replacement, or other repairs where unwanted air might enter the jack. No more oil

showers or worn out threads in the jack when typical pipe drain plugs were used. Simply back out the center

set screw slightly releasing air while leaving the main body attached to the jack.

1/4” Bleed Port

1/8” Bleed Port

297170

297150

Specifications

Material

5/8" Hex, Ledloy

Max Operating Pressure

1000 psi (55 bar)

Line Connections

1/4” NPT or 1/8" NPT

Max Opera ng Temperature

150° F (65° C)

Oil Type

Hydraulic Fluid

Overall Dimensions: Width (inch) Height (inch) Weight (ounce)

297150

.625

.900

1.0 oz.

297170

.625

.900

0.8 oz.

BV1-8A

BV1-4A

1/4” NPT Female to Male

1/8” NPT Male to Male

Specifications

Max Operating Pressure

1000 psi (55 bar)

Line Connections

1/8” NPT, 1/4" NPT or 3/4” NPT

Max Opera ng Temperature

150° F (65° C)

Oil Type

Hydraulic Fluid

Overall Dimensions: Width (inch) Length (inch) Height (inch) Weight (ounce)

BV1-4A

.950

2.050

1.275

4 oz.

BV1-8A

.950

1.900

1.275

3 oz.

BV3-4

1.630

5.875

3.000

16 oz.

Piping Dimension: Length (inch)

BV3-4

2.640

The Maxton Hydraulic Shut Off Ball Valve has been tested specifically for hydraulic elevator applications

and comply with ASME A17.1 / CSA B44.

SHUT OFF BALL VALVE / BLEED PORT

3/4” NPT Female to Female

Summary of Contents for EMV10







































































































Search results

Summary of Contents for EMV10

Reviews:

Brands by name

Popular brands

Maxton EMV10, Manual

Search results

Summary of Contents for EMV10

Reviews:

Brands by name

Popular brands