Maxon SD-270 Series User Manual Download Page 11

Page: 11 / 14

volume for the connected speaker in set in the programming. The default volume is

6. The minimal volume is 0 and the maximum is 9.

Power Save Mode

When user enables the function, The SD-270 will operate in a status to lower power

consumption in standby. If a useful signal is detected, the radio will begin to receive

normally. If no useful signal detected, the radio will revert to power save. Power save

intervals can be set in the programming. Not recommended when using for data

transmission.

Side Tone

This feature, when enabled, transmits the MIC signal via the output from SPK port to

allow user to hear his or her own voice. The feature can also be set via programming.

RSSI Detection

In TX mode, the radio can quickly detect the strength of a useful RF signal and

indicate the strength by analog voltage after calculation and analysis of MCU.

Stronger signal means higher output voltage. The field strength can also be viewed

by serial command.

LED Status Indicator

The LED indicator gives real time status of the radio's operation, Red for TX and

green for RX.

Summary of Contents for SD-270 Series














