background image

LIFT CORP.

11921 Slauson Ave.
Santa Fe Springs, CA. 90670

CUSTOMER SERVICE: 

TELEPHONE (562) 464-0099  TOLL FREE (800) 227-4116

FAX: (888) 771-7713

WARRANTY/ RMA POLICY & PROCEDURE

 

NOTE: For latest version of all Manuals (and replacements), download the

Manuals from Maxon’s website at www.maxonlift.com.  

LIFTGATE WARRANTY

 

 

Type of Warranty:  

Full Parts and Labor

Term of Warranty:  

Standard Liftgates - 2 years from ship date or 6,000 cycles

 

 

Premium Liftgates - 2 years from ship date or 10,000 cycles

This warranty shall not apply unless the product is installed, operated and maintained in accordance with MAXON Lift’s speci

fi

 cations as set forth in 

MAXON Lift’s Installation, Operation and Maintenance manuals. This warranty does not cover normal wear, maintenance or adjustments, damage or 

malfunction caused by improper handling, installation, abuse, misuse, negligence, or carelessness of operation. In addition, this warranty does not 

cover equipment that has had unauthorized modi

fi

 cations or alterations made to the product. 

 

 

MAXON agrees to replace any components which are found to be defective during the 

fi

 rst 2 years of service, and will reimburse for labor based on 

MAXON’s Liftgate Warranty Flat Rate Schedule. (Copy of the Flat Rate is available at 

www.maxonlift.com

.)

All warranty repairs must be performed by an authorized MAXON warranty facility. For any repairs that may exceed $500, including parts and labor, 

MAXON’s Technical Service Department must be noti

fi

 ed and an “Authorization Number” obtained.  

 

 

  

 

 

 

 

All claims for warranty must be received within 30 Days of the repair date, and include the following information:

 

1. Liftgate Model Number and Serial Number

 

2. The End User must be referenced on the claim

 

3. Detailed Description of Problem

 

4. Corrective Action Taken, and Date of Repair

 

5. Parts used for Repair, Including MAXON Part Number(s)

 

6. MAXON R.M.A. # and/or Authorization # if applicable (see below)

 

7. Person contacted at MAXON if applicable

 

8. Claim must show detailed information i.e. Labor rate and hours of work performed

Warranty claims can also be placed online at

 www.maxonlift.com. 

Online claims will be given priority processing.  

 

  

 

 

 

 

 

All claims for warranty will be denied if paperwork has not been received or claim submitted via Maxon website for processing by MAXON’s Warranty 

Department within 30 days of repair date. 

All components may be subject to return for inspection, prior to the claim being processed. MAXON products may not be returned without prior written 

approval from MAXON’s Technical Service Department. Returns must be accompanied by a copy of the original invoice or reference with original 

invoice number and are subject to a credit deduction to cover handling charges and any necessary reconditioning costs. 

Unauthorized returns will be 

refused and will become the responsibility of the returnee. 

Any goods being returned to MAXON Lift must be pre-approved for return, and have the R.M.A. number written on the outside of the package in plain 

view, and returned freight prepaid. All returns are subject to a 15% handling charge if not accompanied by a detailed packing list. Returned parts 

are subject to no credit and returned back to the customer. Defective parts requested for return must be returned within 30 days of the claim date for 

consideration to: 

 

 

MAXON Lift Corp.

10321 Greenleaf Ave., Santa Fe Springs, CA 90670

Attn: RMA#__

MAXON’s warranty policy does not include the reimbursement for travel time, towing, vehicle rental, service calls, oil, batteries or loss of income due to 

downtime. Fabrication or use of non Maxon parts, which are available from MAXON, are also not covered. 

MAXON’s Flat Rate Labor Schedule takes into consideration the time required for diagnosis of a problem. 

All Liftgates returned are subject to inspection and a 15% restocking fee. Any returned Liftgates or components that have been installed or not returned 

in new condition will be subject to an additional reworking charge, which will be based upon the labor and material cost required to return the Liftgate or 

component to new condition.

PURCHASE PART WARRANTY

 

 

 

 

 

 

 

 

 

Term of Warranty: 1 Year from Date of Purchase. 

 

 

 

 

 

 

 

Type of Warranty:  Part replacement only. MAXON will guarantee all returned genuine MAXON replacement parts upon receipt and inspection of parts 

and original invoice.
All warranty replacements parts will be sent out via ground freight. If a rush shipment is requested, all freight charges will be billed to the requesting 

party.

Summary of Contents for DMD-22









































Reviews: