background image

Operating Instructions                                                                                                           WPOP Series

MaxLite CCT Selectable WallMax™ Open Face

®

• To reduce the risk of death, personal injury or property damage from 

fire, electric shock, falling parts, cuts/abrasions, and other hazards 

read all warnings and instructions included with and on the fixture 
box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon 

this equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires 

should be performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or

maintenance of the luminaires, consult a qualified licensed electrician 
and check your local electrical code. 

• DO NOT INSTALL DAMAGED PRODUCT!
• This fixture is intended to be connected to a properly installed and 

grounded UL listed junction box.

WARNING:

RISK OF ELECTRICAL SHOCK

• Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.

• Turn off the power when you perform any maintenance.

• Verify that supply voltage is correct by comparing it with the luminaire label information.

• Make all electrical and grounded connections in accordance with the National Electrical Code 

and any applicable local code requirements.

• All wiring connections should be capped with UL approved wire connectors.

• Do not handle energized fixture when hands are wet, when standing on wet or damp surfaces, or in water.

CAUTION: 

RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing 

or performing maintenance.

• Avoid direct eye exposure to the light source while it is on.

• Account for small parts and destroy packing material, as these may be hazardous to children.

CAUTION: 

RISK OF FIRE

• Keep combustible and other materials that can burn away from luminaire and lamp/lens

• MIN 90°C SUPPLY CONDUCTORS.

© Copyright 2021. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006   Tel: 800-555-5629   Fax: 973-244-7333   Email: [email protected]

General Safety Information

Page: 1
REV: 11/19/21

Picture is for illustration purposes only. 
Your model may vary.

WPOP Series

Operating Temperature: -30°C to 40°C
Rated Voltage: 120-277 Vac 50/60Hz

Summary of Contents for WPOP Series













Reviews: