Maximum Controls MATRIX III MAX 1200FS PRO, Installation Manual

Page: 30 / 42

omron E3K-R10K4 wiring for max pro
Polarity does
NOT
matter
12VDC Out Monitored
4 5 6
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
24 to 240 VDC
1 2
N02 C2
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
PHOTO CLS NC
GND
NOTE: To meet the UL 325 2018 standard,
Type B1 Non-Contact sensor entrapment
protection device MUST be MONITORED
by the gate operator.
NORMALLY CLOSED (NC)
UL325-2018
Wiring to E3K Photocell
DO NOT connect
to NC2 #4.
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR N.C.
UL SENSOR 10K
NSOR N.C
P
NSOR N.C
P
SOR N.
P
SOR N
P
SOR N SOR N
OR N OR N OR
NC2 N02 C2
IMPORTANT:
Photocell MUST be powered
by
12VDC OUT Monitored or
it will NOT be MONITORED.
For 10K Resistor E3K Photocell wiring see next page
UL 2018 Label on packaging
5,3TANDARD-!8&302/&302/-ATRIX))))NSTALL6ERSIONB
Polarity does
NOT
matter
12VDC Out Monitored
4 5 6
C-1 NO1 NC1
LIGHT ON
SENSITIVITY
Min Max
DARK ON
Power
Set switch to
“LIGHT ON”
24 to 240 VAC
VDC 24 to 240
1 2
N02 C2
3
Sensitivity Adjustment:
If the photocell does not respond to an
obstruction, lower the sensitivity by
turning adjustment counter-clockwise.
OK to
use
12VDC
/0%./.,9.#
GND
NOTE: To meet the UL 325 2018 standard,
Type B1 Non-Contact sensor entrapment
protection device MUST be MONITORED
by the gate operator.
Installation Steps:
3ETSWITCHTOh,)'(4/.v
2.
3.
7IRE6POWERTOPHOTOCELL
7IRE /0%./.,9.#
TO PHOTOCELL ./
7IRE '.$ TOPHOTOCELL #
!LIGNPHOTOCELLTOREFLECTOR
!DJUSTSENSITIVITY
UL325-2018
NORMALLY CLOSED (NC)
Wiring to E3K Photocell
DO NOT connect
to NC2 #4.
NC2 N02 C2
IMPORTANT:
Photocell MUST be powered
by
12VDC OUT Monitored or
it will NOT be MONITORED.
For 10K Resistor E3K Photocell wiring see next page
UL 2018 Label on packaging
OPEN ONLY NC
OPEN ONLY 10K
PHOTO CLS NC
OPEN/CLS NC
GND
12VDC OUT
GND
CLS ONLY 10K
OPEN/CLS 10K
12VDC OUT
UL SENSOR 10K
UL SENSOR N.C.
Installation Steps:
3ETSWITCHTOh,)'(4/.v
2.
3.
7IRE6POWERTOPHOTOCELL
7IRE 0(/4/#,3.#
TO PHOTOCELL ./
7IRE '.$ TOPHOTOCELL #
!LIGNPHOTOCELLTOREFLECTOR
!DJUSTSENSITIVITY
CL OSING Direction
Photocell (R eflector)
OPEN ING Direction
Photocell (R eflector)