manualshive.com logo in svg

Maxim Dallas Semiconductor DS3171, General Description Manual, Page: 131 / 234

Share
Download
Maxim Dallas Semiconductor DS3171 General Description Manual Download Page 131

DS3171/DS3172/DS3173/DS3174 

 

 

131 

11 = Output logic 1  

Bits 1 to 0: General-Purpose IO 1 Select [1:0] (GPIO1S[1:0]).

 These bits determine the function of the GPIO1 

pin. 

00 = Input 
01 = Port 1 A status output selected by 

PORT.CR4

:GPIOA[3:0] in port control registers 

10 = Output logic 0 
11 = Output logic 1 

 

 

Register Name: 

GL.ISR 

Register Description: 

Global Interrupt Status Register 

Register Address: 

010h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

 

 

 

 

 

 

 

 

 

Bit 

# 7 6 5 4 3 2 1 0 

Name PISR4 PISR3 PISR2 PISR1 --  -- 

RESERVED

 

GSR 

 

Bits 7 to 4: Port Interrupt Status Register [4:1] (PISR[4:1] ) 

The corresponding bit is set when any of the bits in 

the port interrupt status registers (

PORT.ISR

) are set. The 

INT

 interrupt pin will be driven low when any bit is set 

and the corresponding 

GL.ISRIE

.PISRIE[4:1] interrupt enable bit is enabled. 

Bit 0: Global Status Register Interrupt Status (GSR) 

This bit is set when any of the latched status register bits in 

the global latched status register (

GL.SRL

) are set and enabled for interrupt. The 

INT

 interrupt pin will be driven low 

when this bit is set and the 

GL.ISRIE

.GSRIE interrupt enable bit is enabled. 

 
Register Name: 

GL.ISRIE 

Register Description: 

Global Interrupt Status Register Interrupt Enable 

Register Address: 

012h 

 
Bit 

#  15 14 13 12 11 10  9  8 

Name 

-- -- -- -- -- -- -- -- 

Default 

0 0 0 0 0 0 0 0 

 

 

 

 

 

 

 

 

 

Bit 

# 7 6 5 4 3 2 1 0 

Name  PISRIE4 PISRIE3 PISRIE2 PISRIE1 

-- 

-- 

RESERVED

 

GSRIE 

Default 

0 0 0 0 0 0 0 0 

 

Bits 7 to 4: Port Interrupt Status Register Interrupt Enable [4:1] (PISRIE[4:1])

 When any interrupt enable bit in 

this group is enabled corresponding to a status bit set in the 

GL.ISR.

PISR[4:1] status bit group, the 

INT

 pin will be 

driven low. 

0 = interrupt disabled 
1 = interrupt enabled 

Bit 0: Global Status Register Interrupt Status Interrupt Enable (GSRIE) 

When this interrupt enable bit is 

enabled, and the 

GL.ISR

.GSR status bit is set, the 

INT

 pin will be driven low. 

0 = interrupt disabled 
1 = interrupt enabled 

 

 

Summary of Contents for Dallas Semiconductor DS3171











































































































































































































































Reviews:

No comments