background image

Features 

 

MAX30101 Heart Rate Monitor and Pulse Oximeter 

o

 

Tiny 5.6mm × 3.3mm × 1.55mm 14-Pin Optical Module 

o

 

Integrated Cover Glass for Optimal, Robust Performance 

o

 

Ultra-Low Power Operation for Mobile Devices (< 1mW) 

o

 

Programmable Sample Rate and LED Current for Power Savings 

o

 

High SNR (Signal-to-Noise) ratio, typically greater than 80dB 

 

MAX32664 Sensor Hub 

o

 

Maxim-licensed firmware provides complete algorithmic support for finger heart 
rate and blood oxygen saturation calculations 

o

 

Communicates with host controller over industry standard I

2

C interface. 

o

 

Secure firmware updates authenticated by dedicated bootloader. 

 

3-Axis Accelerometer Provides Greater Accuracy 

o

 

Compensates for motion artifacts. 

Applications/Uses 

 

Portable Medical Devices  

 

Telemedicine  

 

Sensor Hubs  

 

Android or IOS devic 

Introduction 

The MAXREFDES220# provides detailed design information to use Maxim Integrated 
devices to quickly implement end-to-end measurement of heart rate and SpO2 using 
reflective photo plethysmography (PPG). 

The MAX30101 operates from a 1.8V power supply and a separate 5.0V power supply 
for the internal LED. Many device parameters are configurable by the MAX32644. The 
module can be shut down through software with zero standby current, allowing the 
power rails to remain powered at all times. 

The MAX32664 is a small, low cost, power-optimized sensor hub for finger-based pulse 
applications using the MAX30101. The hub collects and processes the output of the 
PPG and accelerometer transparently through a dedicated I

2

C interface. A 

second,standard-mode I

2

C interface connects to the host through a dedicated command 

set. 

A Windows

®

-based GUI configures the sensors and graphically displays raw and 

processed heart rate and SpO2 data. It also provides the ability to collect and log 
sensor output for off-line evaluation. 

The provided MAX32630FTHR board emulates a host system for easy development. 
Source code for the MAX32630FTHR firmware is freely available on the mbed site to 
allow customers to implement their own custom host on any platform. 

Summary of Contents for MAXREFDES220







Reviews: