Maxim Integrated MAX32660 User Manual Download Page 129

Page: 129 / 195

MAX32660 User Guide

Maxim Integrated

Page 129 of 195

11.8

Watchdog Timer Registers

The WDT0 base peripheral address is 0x4000 3000. Refer to

Table 3-1: APB Peripheral Base Address Map

for the addresses

of all APB mapped peripherals.

Table 11-2: Watchdog Timer Registers

Address

Register Name

Access

Description

[0x0000]

WDT0_CTRL

R/W

Watchdog Timer 0 Control Register

[0x0004]

WDT0_RST

R/W

Watchdog Timer 0 Reset Register

1.1.1

Watchdog Timer Register Details

Table 11-3: Watchdog Timer Control Register

Watchdog Timer 0 Control Register

WDT0_CTRL

0x0000 [0x00]

Bits

Name

Access

Reset

Description

rst_flag

R/W

See

description

Reset Flag

If set a watchdog system reset occurred.

0: Watchdog did not cause reset event.
1: Watchdog reset occurred.

30:12

Reserved for Future Use

Do not modify this field.

rst_en

R/W

Reset Enable

Enable/Disable system reset if the

WDT0_CTRL

rst

period

expires. Only reset by

power on reset.

0: Disabled
1: Enabled

int_en

R/W

Interrupt Enable

Enable or Disable the watchdog interrupt.

0: Disabled
1: Enabled

int_flag

R/W1C

Interrupt Flag

If set, the watchdog interrupt period has occurred.

0: IRQ not pending
1: Interrupt period expired. Generates a WDT IRQ if

WDT0_CTRL

int

= 1.

wdt_en

R/W

See

Description

Enable

Enable or disable the watchdog timer. Only reset by a power on reset. To enable
the watchdog timer, the following sequence of writes must be performed.

Write

WDT0_RST

: 0x0000 00A5

Write

WDT0_RST

: 0x0000 005A

Write

WDT0_RST

wdt

: 0x1

0: Disabled
1: Watchdog Timer Enabled. To set this field to 1, perform the sequence shown

above.

Note: This field is reset by a Power-On Reset event only. Other forms of reset do not
reset this field.

Summary of Contents for MAX32660




































































































































































































Search results

Summary of Contents for MAX32660

Reviews:

Brands by name

Popular brands

Maxim Integrated MAX32660, User Manual

Search results

Summary of Contents for MAX32660

Reviews:

Brands by name

Popular brands