background image

2

INDEX

INHALTSVERZEICHNIS

INDEX

INDICE

INDICE

ENGLISH

Page 3 to 15 Page

DEUTSCH

Page 17 to 29 Page

FRANÇAIS

Page 31 to 43 Page

ITALIANO

Page 45 to 57 Page

ESPAÑOL

Page 59 to 71 Page

DEFINITIONS OF SIGNAL WORDS
WARNING:

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTE:

Emphasizes essential information.

DEFINITIONEN DER HINWEISBEZEICHNUNGEN
ACHTUNG!

Zeigt eine eventuell gefährliche Situation an, die den Tod oder schwere Verletzungen zur Folge haben 
könnte, wenn sie nicht vermieden wird.

VORSICHT!

Zeigt eine eventuell gefährliche Situation an, die leichte oder mittelschwere Verletzungen zur Folge 
haben könnte, wenn  sie nicht vermieden wird.

HINWEIS:

Hebt wichtige Informationen hervor.

DÉFINITIONS DES DIFFÉRENTS DEGRÉS D’ AVERTISSEMENTS
AVERTISSEMENT

Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée, pourrait provoquer la 
mort ou des blessure sérieuses.

ATTENTION

Indique une situation éventuellement dangereuse qui, si elle n’est pas contournée, pourrait provoquer 
des blessures légères à moyennement sérieuses.

REMARQUE

Souligne des informations importantes.

DEFINIZIONE DELLE INDICAZIONI DI AVVERTIMENTO
ATTENZIONE:

Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non viene evitata, può 
risultare letale o provocare gravi lesioni.

AVVERTENZA:

Indica l’eventualità che possa verificarsi una situazione pericolosa, la quale se non viene evitata, può 
provocare lesioni di lieve o media entità.

NOTA:

Evidenzia informazioni importanti.

DEFINICIÓN DE LAS INDICACIONES DE ADVERTENCIA
¡ATENCIÓN!

Indica una situación potencialmente peligrosa que podría causar la muerte o graves lesiones si no se 
evita.

¡PRECAUCIÓN!

Indica una situación potencialmente peligrosa que podría causar lesiones menos graves o leves si no 
se evita.

NOTA:

Resalta informaciones importantes.

Summary of Contents for CN650M

















Reviews: