Helpful Hints
If the receiver and / or the transmitter display LLL or HHH instead of the probe temperature,
wait for probe to reach room temperature. If LLL or HHH is still displayed or you get a false
temperature, squeeze the probe jacks harder into the transmitter and twist them back and forth
so they make good contact. If the problem still persists it is likely the internal probe wire has
shorted out either through moisture or heat damage.
Do not immerse the probe in water while cleaning.
Do not allow the probe or probe wire to come into contact with flames.
Within the warranty period, return defective probe to address below along with return address
and we will send you a replacement probe at no charge.
If the temperature displayed seems to read too high or the temperature seems to increase too
quickly, check to make sure the probe tip is not poking through the food to outside. Reposition
the probe tip in the center of the thickest part of food. Avoid touching bone or heavy fat areas.
Cautions:
Always wear a heat resistant glove to touch the stainless steel probe sensors or wires during or
just after cooking. Do not touch with bare hands.
Keep the stainless steel probe sensors and wires away from children.
Clean the stainless steel probes and dry thoroughly after each and every use.
Do not use the receiver in the rain. It is NOT rain proof. The transmitter is rain proof but not
water tight. Do not immerse in water.
Do not expose the plugs of the stainless steel probes or the plug in holes of the transmitter to
water or any liquid. This will result in a bad connecting and faulty readings.
Do not expose the receiver or transmitter to direct heat or surface.
Do not use stainless steel probes in microwave oven.
The Barbecue Thermometer registers temperatures as low as 32 ºF (0 ºC) and as high as 572
ºF (300 ºC). LLL will be displayed below 32 ºF and HHH will be displayed above 572 ºF. Do not
use the stainless probe sensor above 572 ºF. Doing so will deteriorate the wire.
Not Intended for Use by Persons ages 12 and Under.
Cleaning
Always wear a heat resistant glove to touch the stainless steel probe sensors or wires during or
just after cooking. Do not touch with bare hands.
Keep the stainless steel probe sensors and wires away from children.
Wash the metal probe tips with hot soapy water and dry thoroughly. Do not immerse the probe
in water while cleaning.
Wipe the transmitter and receiver with damp cloth. Do not immerse either in water.
Information to user
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the users’ authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
FCC Compliance
Information to user
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the users' authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
LIMITED NINETY DAY WARRANTY
Maverick Industries Inc. warrants the ET-632 REDI CHEK BARBECUE Thermometer to be
free of defects in parts, materials and workmanship for a period of 90 days, from date of
purchase. Should any repairs or servicing under this warranty be required, contact Maverick
Customer Service by email or mail for instruction on how to pack and ship the HD-378 REDI
CHEK BARBECUE Thermometer to Maverick’s National Service Center located as follows:
Maverick Customer Service
94 Mayfield Ave.
Edison NJ 08837
Telephone: (732) 417-9666
email: [email protected]
Do not send any parts or product to Maverick without obtaining a Return Authorization Number
and instructions.
This warranty is VOID if instructions for use are not followed; for accidental damage; for
commercial use; for damage incurred while in transit; or if the HD-378 REDI CHEK
BARBECUE
Thermometer has been tampered with.
This warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
Replacement Probes
To purchase, out of warranty, stainless steel replacement probes please mail us a check to the
address below and specify probe type:
HD-378 Food Probe $12.00/ea
HD-378 BBQ Probe $12.00/ea
Set of probes $20.00/set
All prices include shipping & handling. NJ residents add 7% sales tax.
Attn Customer Service
Maverick Industries, Inc.
94 Mayfield Ave.
Edison NJ 08837
